Electramax eM-50T Podręcznik użytkownika - Strona 5

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Elektroniczna niania Electramax eM-50T. Electramax eM-50T 6 stron. Wireless colour video and audio baby monitor

Drukuj stronę

7.3 Voice-Activated Function (Auto Mode),

This voice-activated mode allows you to set the sensitivity of

audio level that will trigger the monitor. To use voice-

activated function, follow these steps:

Set the sensitivity control on the monitor

to the level you prefer.

Note: The sensitivity level can vary between

0 and 9. A value of 0 gives minimum sensitivity,

a value of 9 gives maximum sensitivity.

Press the Auto button on the front of the monitor.

This will turn off the screen but the power LED will r emain on.

When the sound from the camera reaches the set level, the screen will turn on

automatically. It will turn off again after 30 seconds.

Note: Under/In voice-activated mode, the monitor can only detect signal input from one

camera at a time. The CH button is not functional under Voice-activated mode.

8.0 TROUBLESHOOTING

Should you have any problems operating your eM-50T please refer to the table below. However if the

problems cannot be resolved then please call us on the helpline or email us on [email protected]

Problem

Possible Cause

No signal received on

Batteries may

Parent unit.

be weak/flat.

AC adaptors are

not connected properly.

Different channels

selected on both units.

Either or both units are OFF.

Parent unit is in Auto mode

and sensitivity is set too low.

Poor signal or

Different channels

inference on

selected on both units.

Parent unit.

Microwave Oven in use in

the path of units

The units are out of range.

If power LED is ON but

only voice signal is

detected, the Parent unit

may be in Voice-activated

mode.

Picture on screen

Baby unit is set to

on Parent unit is

NIGHT VISION mode

received in B&W

and not in colour

(See Fig. 12).

Fig. 12

How to Resolve

Replace

Batteries.

Ensure adaptors are properly connected.

If either unit works with batteries but

not with the adaptor, then replace adaptor.

Ensure Baby and Parent units are

set to same channel.

Ensure both units are turned ON.

Either increase the sensitivity and/or

turn Auto mode OFF by pressing the

Auto button on Parent unit.

Ensure Baby and Parent units are set to

same channel.

Move Microwave Oven to different location

lor turn off.

Ensure both units are within range of each

other (approx. maximum range is 300

feet in clear line of sight).

Press Auto button to turn the screen ON.

Change setting to ON. During night/Dark

room environment, picture is received in

B&W when Baby unit is set to NIGHT

VISION mode.

3.0 Fine Tuning the Baby Unit (Camera)

WARNING: please ensure you read Important

Warnings on page 2 of this manual prior to use.

Place the camera in a convenient location,

point the lens towards the observation ar ea

and adjust the angle by rotating the lens

head in a vertical direction. (See Fig. 5)

4.0 Mounting the Baby Unit (Camera)

Fig. 6

Note 1: The monitor reception should be tested before fixing the camera in place. Have

someone hold the camera against the wall in the selected mounting area while you check

the reception on the monitor. If interferences or other problems occur, refer to the

Troubleshooting section. You may need to select a different location in the room for

mounting the camera. A set of fixings for masonry has been included.

Note 2: Where the wall is constructed of plasterboard or an alternative type of material

please consult a qualified person for ascertaining the cor rect fixing to be used.

Note 3: The approximate maximum transmission range is 300 feet (clear line of site),

however the actual transmission distance will be dependant on the number and type of

walls/ceilings/constructions and other obstacles that may reduce the transmission range.

Drill two holes 52mm apart in a line, at the camera mounting position.

Fix the provided mounting plate to the wall using the masonry plugs and fixing scr ews

supplied, (See Fig. 6).

Place the camera against the mounting plate so that the studs on the mounting plate

are adjusted to the keyholes on the back of camera. Then pull the camera down to

slide the studs into the cutout channels, (See Fig. 7).

5.0 Night Vision Setting on the Baby Unit (Camera)

Slide the OFF/ON/NIGHT switch to the NIGHT position. Use this night mode when your baby

or child is in a darkened room. The small LED around the lens allow the night vision facility.

Fig. 8

Fig. 5

Fig. 7