Asus ExpertWiFi EBM68 Skrócona instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Router sieciowy Asus ExpertWiFi EBM68. Asus ExpertWiFi EBM68 2 stron. Ax7800 tri band wifi router

Drukuj stronę

Relocation

THE BEST PERFORMANCE

Locate the AiMesh router and node at the best place.

NOTES:

To minimize interference, keep the routers away from devices like cordless

phones, Bluetooth devices and microwave ovens.

We recommend that you place the routers in an open or spacious location.

EBM68 LED indications

Solid green:

Your EBM68 is starting up.

Solid blue:

Your EBM68 is ready for setup.

Blinking blue:

Your AiMesh router is syncing with AiMesh mode.

Solid white:

Your EBM68 is online and works well.

Solid yellow:

The signal between your EBM68 router and the node is weak.

Solid red:

Your EBM68 router has no Internet connection. / Your node is disconnected from the router.

Support Wall Mount

IMPORTANT!

Only install the wall mount vertically on the wall.

DO NOT install the wall mount horizontally or on the ceiling.

DO NOT mount this equipment higher than 2 meters.

NOTES:

Wall anchor and screw sizes are for reference only.

It is recommended to use the attached anchor and screws.

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our

environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other

components, as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed

recycling information in different regions.

REACH

Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we

published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause undesired operation.

FCC regulations restrict the operation of this device to indoor use only.

This device cannot operate as a subordinate between separate buildings or structures.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Caution Statement:

WARNING : Any changes or modifications not expressly approved by the party responsible for compliance could void your

authority to operate the equipment.

FCC RF Exposure information:

This device meets the government's requirements for exposure to radio waves. This device is designed and manufactured

not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications

Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific

Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating

positions accepted by the FCC with the EUT transmitting at the specified power level in different channels. The FCC has

granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC

RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant

section of www.fcc.gov/oet/ea/fccid.

WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

Prohibition of Co-location

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

IMPORTANT NOTE:

Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain

compliance with FCC exposure compliance requirement, please follow operation instruction as documented in this manual.

WARNING! This equipment must be installed and operated in accordance with provided instructions and the

antenna(s) used for this transmitter must be installed to provide a separation distance of at least 31 cm from all

persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Safety Notices

• Use this product in environments with ambient temperatures between 0°C(32°F) and 40°C(104°F).

• Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating.

• DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been damaged.

• DO NOT place or drop objects on top and do not shove any foreign objects into the product.

• DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms.

• DO NOT cover the vents on the product to prevent the system from getting overheated.

• DO NOT use damaged power cords, accessories, or other peripherals.

• If the Adapter is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.

• DO NOT mount this equipment higher than 2 meters.

FAQ

Q1:

Does the AiMesh router support Access Point mode?

A: Yes. You can choose to set the AiMesh router as router mode or access point mode. Please

go to web GUI (https://www.expertwifi.net), and go to the page Administration > Operation

Mode.

Q2:

Could I setup wired connection between AiMesh routers (Ethernet backhaul)?

A: Yes. AiMesh system supports both wireless and wired connection between AiMesh router

and node to maximize throughput and stability. AiMesh analyzes the wireless signal strength

for each frequency band available, and then determines automatically whether a wireless or

wired connection is best to serve as the inter-router connection backbone.

6.0

2.3

32.0

-0.50

0.15

-0.50

4.8-5.4

8.9-9.5

25.8-27.8

Q3:

Where can I find more information about Mesh WiFi system?

A: Technical support site: https://www.asus.com/support

Avertissements de sécurité

• Utilisez ce produit dans un environnement dont la température ambiante est comprise entre 0˚C (32°F) et 40˚C (104°F).

• Référez-vous à l'étiquette située au dessous du produit pour vérifier que l'adaptateur secteur répond aux exigences de

tension.

• NE PAS placer sur une surface irrégulière ou instable. Contactez le service après-vente si le châssis a été endommagé.

• NE PAS placer, faire tomber ou insérer d'objets sur/dans le produit.

• NE PAS exposer l'appareil à la pluie ou à l'humidité, tenez-le à distance des liquides. NE PAS utiliser le modem lors d'un

orage.

• NE PAS bloquer les ouvertures destinées à la ventilation du système pour éviter que celui-ci ne surchauffe.

• NE PAS utiliser de cordons d'alimentation, d'accessoires ou autres périphériques endommagés.

• Si l'adaptateur est endommagé, n'essayez pas de le réparer vous-même. Contactez un technicien électrique qualifié ou

votre revendeur.

• Pour éviter tout risque de choc électrique, débranchez le câble d'alimentation de la prise électrique avant de toucher au

système.

• Ne placez pas cet appareil à une hauteur supérieure à 2 mètres.

Compliance Statement of Innovation, Science and Economic Development Canada (ISED)

This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired operation of the device.

Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel

mobile satellite systems.

CAN ICES-003(B)/NMB-003(B)

Radio Frequency (RF) Exposure Information

The radiated output power of the ASUS Wireless Device is below the Innovation, Science and Economic Development

Canada radio frequency exposure limits. The ASUS Wireless Device should be used in such a manner such that the potential

for human contact during normal operation is minimized.

This equipment should be installed and operated with a minimum distance of 30 cm between the radiator any part of your

body.

This device has been certified for use in Canada. Status of the listing in the Innovation, Science and Economic Development

Canada's REL (Radio Equipment List) can be found at the following web address:

http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html

Additional Canadian information on RF exposure also can be found at the following web:

https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Déclaration de conformité de Innovation, Sciences et Développement économique Canada (ISED)

Le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit

pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

La bande 5150 – 5250 MHz est réservée uniquement pour une utilisation à l'intérieur afin de réduire les risques de

brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

CAN ICES-003(B)/NMB-003(B)

Informations concernant l'exposition aux fréquences radio (RF)

La puissance de sortie émise par cet appareil sans fil est inférieure à la limite d'exposition aux fréquences radio d'Innovation,

Sciences et Développement économique du Canada (ISED). Utilisez l'appareil sans fil de façon à minimiser les contacts

humains lors d'un fonctionnement normal.

Cet équipement doit être installé et utilisé avec un minimum de 30 cm de distance entre la source de rayonnement et votre

corps.

L'utilisation de cet appareil est autorisée au Canada. Pour consulter l'entrée correspondant à l'appareil dans la liste

d'équipement radio (REL - Radio Equipment List) d'Innovation, Sciences et Développement économique du Canada,

rendez-vous sur :

http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html

Pour des informations supplémentaires concernant l'exposition aux fréquences radio au Canada, rendez-vous sur : https://

www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

For product available in the US/Canada market, only channel 1~11 can be operated. Selection of other channels is not

possible.

Pour les produits disponibles aux États-Unis et au Canada, seuls les canaux 1 à 11 peuvent être utilisés. La sélection d'autres

canaux n'est pas possible.

This device is restricted for indoor use only.

Cet appareil convient uniquement à un usage intérieur.

FREQUENTLY ASKED QUESTIONS

Follow the setup steps to establish a connection between the AiMesh router and node

via WiFi first.

Place the node in the ideal locations for best coverage. Run an Ethernet cable from the LAN

port of the AiMesh router to the WAN port of AiMesh node.

Router

LAN-WAN

AiMesh system will auto-select the best path for data transmission, whether

wired or wireless.

Service and Support

Video Tutorials

https://www.asus.com/support

https://qr.asus.com/wl_videotutorials

Node