Dovre 1800W Instrukcja instalacji i obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Kominek wewnętrzny Dovre 1800W. Dovre 1800W 5 stron. Cast iron fireplace

Drukuj stronę

Dovre 1800W, 2700W and

2000MFR Cast Iron Fireplace

Installation and Operating

Manual

These instructions should be read carefully

and saved by the

user for future reference

Never install appliance in tight fitting recess.

The installation should not be back filled with any

materials

Free air space should be allowed to the back, sides

and top of the appliance within the recess

We recommend that older chimneys without flue

liners are lined using a suitable liner of at least

200mm (150mm for Mini) diameter for use with

solid fuel burning appliances.

REGULATIONS

IMPORTANT

Before commencing the installation of your Dovre

appliance it is recommended that the instructions are

read and clearly understood.

HEALTH AND SAFETY AT WORK ACT 1974

The installer should comply with the Health and Safety

at Work Act 1974 and with particular reference to the

following:-

HANDLING

Adequate facilities should be provided for handling the

appliance.

GLASS

Extra care should be taken to avoid accidents and

breakage.

FIRE CEMENT

Care should be taken to avoid fire cement contacting the

skin. The material is caustic and in the event of contact

being made, wash off immediately with clean water.

CURRENT BUILDING REGULATIONS AND RELEVANT

CODES OF PRACTICE MUST BE OBSERVED.

ASSEMBLY

Remove all packaging materials

Remove all loose components including grates,

ashpan, fuel retainers, baffle plate and fixings pack.

Fit the door knobs, door latch and air slides (see

illustrations opposite)

For built in installations only. If a freestanding

application with a canopy is required proceed to 5.

For convenience, place 2 pieces of 50mm square

timber on the floor and lay the appliance on its back

on the two timbers battens. Fit the 4 cast iron legs

and levelling bolts.

NOTE: IF THE APPLIANCE IS GOING TO BE INSTALLED

WITH A CANOPY IN A FREESTANDING SITUATION IT

WILL NOT BE NECESSARY TO FIT THE LEGS.

Stand the appliance on a level surface in the upright

position and adjust the levelling bolts to ensure the

appliance is level side to side and front to back.

NOTE: THE DOORS ON YOUR DOVRE 2000 HAVE

BEEN ACCURATELY FITTED IN OUR FACTORY. (SEE

PAGE 3) IN CASE YOU DO FIND A PROBLEM IN

OPERATING THE DOORS, REPORT BACK TO YOUR

DEALER NOW. DO NOT ATTEMPT TO PROCEED WITH

THE INSTALLATION. DOVRE CAN NOT ACCEPT

RESPONSIBILITY FOR INCORRECT DOOR ALIGNMENT

AFTER THE APPLIANCE HAS BEEN INSTALLED.

Fit the top dome, flue damper if required (see

illustrations below) (2700W and 2000MFR models

only) and the flue spigots using a small amount of

fire cement on the joints.

Model: 2000MFR

Model: 2700W / 2000MFR

a&b

assembly of

Air Slides

c&d

assembly of

Door knobs/

Latches and

Legs

assembly of

Smoke Dome

assembly of

Flue Damper

APPLIANCE DOORS - IMPORTANT

NOTE: The doors on your

Dovre 2000 have been

accurately fitted in our factory.

In case you do find a problem

in operating the doors, report

back to your dealer now. Do

not attempt to proceed with

the installation. Dovre can not

accept responsibility for

incorrect door alignment after

the appliance has been

Fig.1

installed. Refer to page 2 of

this manual.

IMPORTANT: The following

stages should be used when

closing the doors on your

Dovre 2000 stove

Pull both sets of doors

together (see fig1).

Locate right hand side

door catch over adjustable

Fig.2

grub screw on left hand

door (see fig2).

Holding door knob push

left hand door.

While maintaining

pressure on left hand door

use right hand door knob

to pull door towards you

at the same time bringing

both doors together

(see fig3).

Fig.3

NOTE: Fixing brackets are supplied with the canopy but due to the variations in sizes of openings, it may

be necessary to support the canopy with your own adapted bracket arrangements.

INSTALLATION

FREE-STANDING INSTALLATIONS WITH CANOPIES

This type of application is often for large inglenook

fireplaces

with

wide

chimneys.

recommended that a liner be fitted if the chimney is

unlined.

There are two methods of installing the appliance on the

hearth.

Appliance mounted on a Dovre Base Support (part

ref MBP or SBP)

Appliance standing directly on the hearth

FOR FREE STANDING INSTALLATIONS IT WILL NOT BE

NECESSARY TO FIT THE SET OF FOUR LEGS SUPPLIED.

STEP 1

Position the appliance in the inglenook allowing a

minimum space of 100mm between the back of the

appliance and the back wall of the inglenook (see

illustration opposite).

STEP 2

Connect the appliance to the chimney using 316 grade

1mm thick stainless steel flue pipe. The pipe diameter

should be 200mm min (150mm for 1800W mini series). If

the flue damper has been fitted (2700W Standard and

2000MFR Super models only), it will be necessary to

install a cleaning access door in the flue pipe or chimney.

Your Dovre dealer will be pleased to advise on the best

method to use.

ON NO ACCOUNT SHOULD THE WEIGHT OF THE

FLUE LINERS BE CARRIED ON THE APPLIANCE. ALL

FLUES AND FLUE LINERS MUST BE SUPPORTED

INDEPENDENTLY OF THE APPLIANCE. FAILURE TO

FOLLOW THIS INSTRUCTION WILL LEAD TO

DISTORTION AND FRACTURING OF THE APPLIANCE

CASTINGS.

STEP 3

Fit the canopy ensuring that a minimum distance of

15mm is allowed between the canopy and the back wall

of the inglenook. This will allow the circulation of warm

air into the room.

WHEN FITTED WITH CANOPY CM3 - CS3

MINI

STANDARD

SUPER

100

410

625

695

950

1070

1435

1770

1840

WHEN FITTED WITH CANOPY CM2 - CS2

100

410

625

695

700

685

1185

1385

1455

* Minimum Dimensions. All Dimensions in Millimetres.

strongly