AMSEC ESL20 Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Zamki AMSEC ESL20. AMSEC ESL20 4 stron. Electronic safe lock

Drukuj stronę

American Security Product Co.

2.4 If the lock fails to open or acts strange, replace the batteries with good quality fresh alkaline 9-

volt batteries. To replace the batteries, simply turn the keypad housing counter-clockwise to

the stop and pull it away from the base. Un-snap the old batteries and clip on the new ones.

Position them in the pocket at the bottom of the housing and replace it, watching that the wires

are not pinched. You should replace your batteries once a year to prevent corrosion damage

from leaking batteries.

2.5 During any input sequence, if you make a mistake, you can press "C" to clear the previous

input and start over again.

2.6 The ESL20 uses a fixed length 6 (six) digit combination.

2.7 Use only your fingers to key the combination. Sharp objects will result in damage, which is not

covered by the warranty.

2.8 If at any time during opening or combination changing the unit is left without input for 10

seconds, it returns to a resting condition. If this occurs during a combination change, the Old

Combination is retained.

2.9 At any time during opening or combination changing the unit will register the first 5 digits of the

combination into the "buffer" that receives input. The 6

pressed. For example, if your press C-1-2-3-4-5-7-4-5-2-7-6-# the program recognizes only

the C-1-2-3-4-5-6-# input. The last numeric key pressed continues to replace the one prior

until the "#" key is pressed to indicate completion. This is a security feature that allows you to

baffle an on-looker that may be trying to memorize your combination. This is the electronic

equivalent to a Spy proof Dial.

Users

There are 10 User Combinations possible. The Master User (User 0) is the one and only code that

is allowed to control all the other users, their access privileges and function setting. Users 1-8 are

only active if Multi-User mode is Enabled and the individual User Number has been Enabled and a

combination entered for that user by the Master User.

3.1 User 0:

Designated the Master User. Has control over all Subordinate Users and setting of

all functions.

3.2 Users 1 through 8: Referred to as Subordinate Users. They only have access and privileges

as the Master User assigns them.

3.3 User 9:

Armored Car Code. This is a special code used only for the purpose of bypassing

the Time Delay. This code will not open the lock alone, only authorize an opening when Time

Delay is active.

Combination Changing

One of the strengths of an electronic safe lock is the quick and easy changing of the

combination(s). This adds to security because you can change it at will if you suspect your

combination is known by others.

The combination change method for the Primary code (Master User) can be done two ways, with or

without a User Number. All combination changes require and authorization code and two entries of

the new combo as verification.

Note: In the event that Function 60 (Subordinate Combo Change) is set to Disable (F60=0), only

the Master Code will authorize a change.

Document Part No. 4305149, Revision C

digit will be the last numeric key

18 Sept. 2000

American Security Product Co.

4.1 Master User Code change:

At any time, the Master User combo can be changed by keying:

C - # - (Old Master Code) - # - (New Master Code) - # - (New Master Code) - #

4.2 Multiple User Mode Change and F60=1: Changing of any combination, including the Master

User Code, can be changed by the following sequence:

C- # - (User No.) - # - (Old User Code) - # - (New User Code) - # - (New User Code) - #

4.3 In the event Function 60 is Disabled (F60=0) or you are adding a new User, then the combo

change must be authorized with the Master User's code:

C- # - (User No.) - # - (Master Code) - # - (New User Code) - # - (New User Code) - #

Combination Change Examples

The Master Combo is 159260 and you wish to change it to 918273. Do the following:

C-#-0-#-159260-#-918273-#-918273-#

User 5's combination is 342312 and you wish to change it to 768798

C-#-5-#-342312-#-768798-#-768798-#

User 5's combination is unknown and you wish to set it to 768798, the Master Combo is 159260

C-#-5-#-159260-#-768798-#-768798-#

Lock Feature Setting and Function Codes.

The ESL20's advanced features are controlled only by the Master User, and are set using Function

Codes. A function can be turned on and off, or set, using the Function Code with the Master User

code as authorization for changing or setting the function. A Function Code is a 2-digit code that

associates to a particular setting. Each Function Code has a default, or standard setting, which is in

the lock when there have been no changes or after a Function Reset (F99) has been executed.

They are as follows.

Function Code List

Function

Function Description

Time Delay Mode Enable/Disable

Set Time Delay Period

Set Open Period

Multiple User Mode Enable/Disable

Add/Enable a User Combo

Disable a User Combo

Disable All Users

Duress Mode Enable/Disable

Dual Combo Mode Enable/Disable

Enable/Disable Two Subordinate Combos Opening

Armored Car Time Delay Bypass Enable/Disable

Enable/Disable Subordinate Authorization of TDL Bypass

External Control Port Enable/Disable

Subordinate User Combo Change Enable/Disable

Reset All Functions to Default settings

C-#-159260-#-918273-#-918273-#

Enable=1, Disable=0

Setting

Range

1 or 0

1 to 99

1 to 9

1 or 0

1 to 8

1 or 0

Default