Electrolux CARAVAN RM 4601 Podręcznik - Strona 9

Przeglądaj online lub pobierz pdf Podręcznik dla Lodówka Electrolux CARAVAN RM 4601. Electrolux CARAVAN RM 4601 11 stron.

Drukuj stronę

1. Operating Instructions

connecting permanently operating appliances of this

type in the United Kingdom). All connectors etc. should

be of a type specifically designed for the type and

diameter of the connection pipe used, and screwed

joints should be sealed with a joining compound approved

for use with bottled gas.

The gas supply pipe should be connected to the gas inlet

pipe (outside diameter 8 mm) by means of a suitable

gas-tight compression fitting, e.g. olive.

In making the connection to the refrigerator, a union gas

cock of an approved type bottled-gas must be incorpo-

rated in the supply line in a position which is readily

accessible to the user. For eventual servicing purposes,

the union should be on the outlet side of the cock and

the pipework should be positioned so as not to prevent

the refrigerator from being readily withdrawn.

On completion of installation, the system must be

pressure tested by a qualified technician.

ELECTRICAL CONNECTION

The electrical installation must be carried out in a proper

and durable manner, taking into account all relevant

regulations and codes of practice. For mains voltage

operation, it is important that the circuit to and in the

caravan is effectively earthed.

For connection to a 230-240 V electricity supply, the

refrigerator has a 3-core mains lead which is intended

for connection to a properly earthed plug and socket

outlet. The socket outlet should be fitted in the caravan

in a position readily accessible to the user, within reach

of the mains lead. In the United Kingdom, the plug and

socket outlet should be of the non-reversible type.

As the colours of the wires in the mains lead of this

appliance may not correspond with the coloured mark-

ings identifying the terminals in your plug, proceed as

follows:

the wire which is coloured Green and Yellow must be

connected to the terminal in the plug which is marked

with the letter E or by the earth symbol

coloured Green or Green and Yellow,

the wire which is coloured Blue must be connected to

the terminal which is marked with the letter N or

coloured Black,

the wire which is coloured Brown must be connected

to the terminal which is marked with the letter L or

coloured Red.

WARNING- THIS APPLIANCE MUST BE EARTHED

IMPORTANT

The wires in this mains lead are coloured in accordance

with the following code:

green/yellow:

blue:

brown:

In the United Kingdom, the plug or circuit to the refriger-

ator must be fitted with a fuse not greater than 5 amps.

If a 13 amp. (B.S. 1363) fused plug is used, it should be

earth

neutral

live

fitted with a 3 amp. fuse, ASTA approved to B.S. 1362.

In other countries, the fuse rating will depend upon the

voltage and local practice.

230-240 V Supplies.

Check that the voltage stated on the data plate is the

same as the mains voltage in use (230-240 V).

Plug the 230-240 V refrigerator power cord into an easily

accessible wall socket.

Electrical leads must be routed and secured so

that they cannot come into contact with hot or

sharp parts of the refrigerator.

12 V Supplies

The 12 V connection of the refrigerator is shown in fig. 4.

Connect the refrigerator to the vehicle battery or alter-

nator by a direct cable, (check the polarity).

The connection is made to the terminal block (fig. 7

"Heater"). To avoid a voltage drop, the cross section area

of the connecting cable between battery/alternator and

the refrigerator must be 10 mm

To ensure satisfactory operation, the positive lead must

be fitted with a fuse rated at max. 25 A.

To prevent the refrigerator from draining the battery,

make sure that the current supplied to the caravan is cut

off when the vehicle engine is not running, for example

by fitting an ignition control relay.

12 V supply of reigniter and interior light

The reigniter and the interior light must be connected to

a separate 12 V battery.

Connect the battery to the terminal block (fig. 7 "Reigni-

ter, Lamp"). Be careful not to make the wrong positive

and negative connections.

The reigniter should not be connected directly to a

battery charger but only over a battery.

Interior light - bulb - change

If the bulb has to be replaced, proceed as follows:

Remove cover of the lamp by pushing it backwards.

, or

Remove the bulb.

Put in a new bulb (12 V, max. 5 W).

Spare part number for bulb: 200 72 90-03.

Push the lamp cover back in place.

FIG. 7