Bosch 800 Series Instrukcja instalacji - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Zmywarka Bosch 800 Series. Bosch 800 Series 29 stron. Built-in wall ovens
Również dla Bosch 800 Series: Instrukcja instalacji (24 strony), Instrukcja instalacji (40 strony), Instrukcja obsługi i konserwacji (12 strony), Instrukcja instalacji (23 strony), Instrukcja instalacji (28 strony), Instrukcja instalacji (32 strony), Instrukcja obsługi (32 strony), Instrukcja instalacji (32 strony), Skrócona instrukcja obsługi i bezpieczeństwa (7 strony), Instrukcja obsługi i konserwacji (40 strony), Instrukcja instalacji (40 strony), Instrukcja instalacji (32 strony), Instrukcja instalacji (40 strony), Instrukcja instalacji (48 strony), Instrukcja obsługi i konserwacji (33 strony), Instrukcja obsługi i konserwacji (49 strony), Skrócona instrukcja obsługi (7 strony), Skrócona instrukcja obsługi i bezpieczeństwa (13 strony), Instrukcja instalacji (32 strony), Instrukcja serwisowa (36 strony), Instrukcja obsługi i konserwacji (24 strony), Instrukcja obsługi i konserwacji (40 strony), Instrukcja instalacji (28 strony)

Drukuj stronę
Bosch 800 Series Instrukcja instalacji
Avoiding General Hazards
Do not use the dishwasher until it is completely
installed. When opening the door on an uninstalled
dishwasher, carefully open the door while supporting
the rear of the unit. Failure to follow this warning can
cause the dishwasher to tip over and result in serious
injury.
Before installing the "L"-shaped supplied countertop
mounting brackets (select models), decide which
method will be used to secure the dishwasher into its
opening. Once these mounting brackets are installed
on the dishwasher, removing them is difficult and will
damage the mounting brackets and the dishwasher.
In some conditions, hydrogen gas can form in a hot
water system that has not been used for weeks.
Hydrogen gas is explosive.
Before filling a dishwasher from a system that has
been off for weeks, run the water from a nearby faucet
in a well ventilated area until there is no sound or evi-
dence of gas.
Temperatures required for soldering and sweating will
damage the dishwasher's base and water inlet valve.
If plumbing lines are to be soldered or sweated, keep
the heat source at least 6" (152.4 mm) away from the
dishwasher's base and water inlet valve.
Removing any cover or pulling the dishwasher from the
cabinet can expose hot water connections, electrical
power and sharp edges or points. Handle with care.
Avoiding Electrical Shock/Fire Hazards
Do not allow the electrical and water supply lines to
touch. Separate channels are provided under the
dishwasher.
Do not work on an energized circuit. Doing so could
result in serious injury or death. Only qualified electri-
cians should perform electrical work. Do not attempt
any work on the dishwasher electric supply circuit
until you are certain the circuit is de-energized.
Make sure electrical work is properly installed. There
should be no loose electrical connections. Ensure all
electrical connections are properly made.
4
WARNING
The customer has the responsibility of ensuring that
the dishwasher electrical installation is in compliance
with all national and local electrical codes and
ordinances. The dishwasher is designed for an
electrical supply of 120V, 60 Hz, AC, connected
to a dishwasher-dedicated, properly grounded
electrical circuit with a fuse or breaker rated for 15
or 20 amps. Electrical supply conductors shall be a
minimum #14 AWG copper only wire rated at 75°C
(167°F) or higher.
This appliance must be connected to a grounded
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the appliance. Do not
use extension cords.
Avoiding Plumbing/Scalding Hazards
Do not perform any work on a charged hot water
line. Serious injury could result. Only
qualified plumbers should perform plumbing work. Do
not attempt any work on the dishwasher hot water
supply plumbing until you are certain the hot water
supply is shut off.
Do not over tighten the 90° elbow. Doing so
may damage the water inlet valve and cause a water
leak.
Temperatures required for soldering and sweating
will damage the dishwasher's water inlet valve. If
plumbing lines are to be soldered or sweated,
keep the heat source at least 6" (152.4 mm) away
from the dishwasher's water inlet valve.
Check local plumbing codes for approved
plumbing procedures and accessories. All plumbing
should be done in accordance with national and local
codes.
These instructions depict an installation method
for stainless steel braided hose or PEX hot water
supply lines. If using copper tubing or other
material for water supply, defer to a licensed
plumber for proper installation.
Proposition 65 Warning:
This product may contain a chemical known to the State of
California, which can cause cancer or reproductive harm.
Therefore, the packaging of your product may bear the following
label as required by California:
STATE OF CALIFORNIA PROPOSITION 65 WARNING:
WARNING
Cancer and Reprodutive Harm - www.P65Warnings.ca.gov
4