DRAKE PS151 Skrócona instrukcja obsługi

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Zasilanie DRAKE PS151. DRAKE PS151 1 stron.
Również dla DRAKE PS151: Skrócona instrukcja obsługi (2 strony)

Drukuj stronę

Power Supply

The PS150 and PS151 power supplies are designed to

provide power for Drake model SCT1860, SCT2860,

SCT3860, and SCT4860 transcoders when mounted in

the model RMT150 rack mounting tray. The PS150 can

power up to a full tray of 10 SCT1860s. The PS151 can

power a full tray of 10 of any mix of the transcoder models

listed above. Either power supply also provides an

interface between a PC or modem and the transcoders

via the RS232 DB9 connectors, providing remote

programming and monitoring capabilities.

SPECIFICATIONS

GENERAL

Power Requirements: -------------------- 100 VAC to 240 VAC

(and -10%/+10% of end limits)

Frequency: ------------------------------------------------- 47-63 Hz

AC Input Power (max), PS150/PS151: ------105/150 Watts

Operating Temperature Range: ------------------- 0 to +50

Internally Mounted (50 mm) Axial Fan

(12 VDC @ 140 mA): -------------------------- 12 CFM (ft

Output Voltages, PS150/PS151:--- +3.3 VDC @ 5.0/10.0 A

MECHANICAL

Dimensions: (WxHxD): ---4.25in. W x 3.33in. H x 10.5in. D

Weight: -------------------------------------2.6 lbs. (PS150)

CONNECTORS

RS232 Out/In: ----------- (2) Type DB-9 interface connectors

DC Output: --------------- (10) Molex 39-31-0060

(Power supply assembly employs short circuit and

overvoltage protection).

AC Power Cord: --------- 54" with USA, 3 prong, 120 V plug

PS150/151 REAR PANEL CONNECTIONS

1. AC Input - The power supply accepts standard 100 to

240 VAC, 50/60 Hz inputs (and -10%/+10% of that voltage

range). A 120 V, USA standard cord is supplied.

2. DC Output - The polarized connectors provide 10 sets

of output connections for the compatible transcoder units.

3. RS232 Remote Control Interface - If the SCT

system transcoders are to be controlled from a PC via the

RS232 interface, the serial port cable from the PC should

be connected to the 'RS232 IN' connector on the supply.

The 'RS232 OUT' connector is used to connect to the

'RS232 IN' port on another PS150/151 or to a PS100 if

additional transcoders are to be controlled. This process

may be repeated until a maximum of 7 PS150/151s (70

transcoders max.) are connected. In addition, up to 63

SCT860s could also be controlled by the same connec-

tion if PS100s are also daisy changed in this connection.

R.L. DRAKE COMPANY

230 INDUSTRIAL DRIVE

FRANKLIN, OHIO 45005 U.S.A.

CUSTOMER SERVICE AND PARTS TELEPHONE: +1 (937) 746-6990

TELEFAX: +1 (937) 806-1576

WORLD WIDE WEB SITE: http://www.rldrake.com

PS150/151 POWER SUPPLY

INSTALLATION

Install the PS150 or PS151 in the RMT150 rack tray by positioning it at the

far right side of the tray as viewed from the front panel of the RMT150.

Before pushing into the final mounting location, make sure that the two

hooks located at the bottom of the rear panel on the power supply, hook

over the back edge of the RMT150 - these will secure the rear of the supply

after it has been pushed forward into its final position. Position the supply

so that the LCD and all pushbuttons are in their proper position in the front

panel of the RMT150 and that the buttons are protruding all the way through

the panel holes. Install the two screws, that are provided with the supply,

through the holes on either side of the display opening in the RMT150

front panel and into the threads of the power supply. Tighten snuggly.

Connect the power cables between the transcoders and the power supply.

Note that each power output connector on the supply is numbered, from 1

through 10. The unit ID of the connected transcoder will be determined by

which socket on the supply its power cable is plugged into. Normally, the

leftmost transcoder, as viewed from the front panel, will be number 1 with

transcoders connected in sequence to the right. The rightmost transcoder

/min.)

will thus be plugged into socket number 10 on the supply. Note that

transcoders do not have to be connected in any specific numerical order

but the above method is preferred to make it easier to identify a particular

+5 VDC @ 9.0/10.0 A

transcoder during setup, if necessary.

+12 VDC @ 1.5/3.0 A

Carefully route the power cable for the front mounted fans between the

power supply and the adjacent transcoder and plug the fan cable into the

socket on the rear of the supply, just above the line cord.

When all cables are connected, plug the line cord into a nominal 120 VAC

3.5 lbs. (PS151)

outlet.

auto run routine should produce a menu providing three options:

1) Install SCT Control Program.

2) View SCT Control Program Instruction Manual, and other manuals for the

PS150/PS151, SCT1860, SCT2860, SCT3860, SCT4860, SCT860, SCT860E,

100 2365, and 100 2366.

3) Install Adobe Acrobat Reader.

To install the control software, choose the "Install SCT Control Program" option. If

the CDROM does not start automatically, Click on the "My Computer" icon on your

PC desktop, then click on the CDROM drive icon. To install the control program,

click on the setup.exe file on the CDROM. Follow the prompts and when the

program has been installed successfully, the "DRAKE DIGITAL, R.L. Drake SCT

Control Program" icon will appear on the PC desktop.

print the detailed program Instruction Manual by selecting option 2, "View SCT

Control Program Instruction Manual" from the auto run menu, or by clicking on the

Instruction Manual.pdf file on the CDROM. If Acrobat Reader is not installed

on your system, select option 3 from the auto run menu or click on the

rs405eng.exe file on the CDROM to install a complimentary copy.

INSTALLING THE PC SOFTWARE FOR THE

DRAKE TRANSCODER CONTROL PROGRAM

To install the control software, place the CDROM in the PC CDROM tray. The

If you have Acrobat Reader installed on your system, you may view and/or

TM is a trademark of the R.L. Drake Company

Printed in the U.S.A.