Draper 145001 Instrukcje instalacji i obsługi - Strona 3
Przeglądaj online lub pobierz pdf Instrukcje instalacji i obsługi dla Ekran projekcyjny Draper 145001. Draper 145001 7 stron. 220v electric projection screen
Drukuj stronę
Ultimate Access E and V 220V
Section 2 - Hanging Screen
Please Note: When locating viewing surface and checking clearance
for screen operation, ensure that surface is centered in the case.
1. Engage each case mounting bracket
housing
and tighten set screws.
(Fig. 2)
2. Screen should be sufficiently supported to withstand vibration.
Please Note: A hoisting bracket is included on each end of the case to
aid in overhead installation.
3. Ensure that fasteners are of adequate strength and suitable for the
mounting surface chosen. Supporting hardware such as chains,
cables, two 3/ 8 "
rods, etc., must be precisely vertical.
(9.5 mm)
4. Entire bottom of case must be readily accessible after installation
is complete.
5. Front, back, and top of case must be straight—not forced to warp
or bow.
CAUTION: Screen case and flange are not designed to serve as ceiling support.
6. Do not seal unit in ceiling until electrical connections have been made and screen
operates successfully.
Please Note: If case is painted on location, removal of roller/fabric assembly is
recommended prior to painting. If not removed, slot on bottom of case should be
shielded to protect viewing surface from paint splatters/overspray.
Section 3 - Bottom Access Panel/Trap Door
Opening and Closing
1. To access inside of screen case, disengage spring latch at center, followed by latches
at each end.
2. To disengage, slide latch lever towards center of screen case
gently on trap door assembly.
Please Note: Latch levers are somewhat concealed from view. Locate with trap door
open by feeling for vertical latch lever above door about 3"
and near center of case.
3. Assembly will swing down and open
4. Pivot prop arms at each end of trap door assembly. Prop arms will engage with a hole
in each endcap to hold trap door assembly fully open. To close trap door assembly
disengage prop arms from endcaps and pivot over access panel.
Figure 4
CAUTION: Beware of pinch
points along closure.
with top of
(attached to case)
, then pull down
(Fig.3)
from case endcaps
(76mm)
.
(about 135˚)
HOISTING
HOISTING
BRACKET
BRACKET
CASE
CASE
MOUNTING
MOUNTING
BRACKET
BRACKET
TYPICAL
1
INSTALLATION
With typical installation, brackets may be
TYPICAL
angled to meet installation requirements.
1
INSTALLATION
With typical installation, brackets may be
angled to meet installation requirements.
Please Note: Extra brackets must be ordered for
alternate installation.
ACCESS DOOR
ACCESS DOOR
SUPPORT
SUPPORT
BRACKET
BRACKET
Figure 3
5. Swing trap door assembly upward, stopping just before
latch levers hit bottom flanges of endcaps
case where appropriate)
6. Pull latch levers toward center of screen case to allow trap
door assembly to be pivoted to its closed position.
Please Note: Ensure that latch levers engage fully with case
endcaps
page 3 of 7
HOISTING
HOISTING
BRACKET
BRACKET
⁷� ₈
"
(22
)
MM
⁷� ₈
"
ELECTRICAL
(22
)
MM
CUTOUT
ELECTRICAL
CUTOUT
ALTERNATE
INSTALLATION
ALTERNATE
Additional set of brackets required
but NOT included.
INSTALLATION
Additional set of brackets required
but NOT included.
Figure 2
E
I D
S L
ACCESS
ACCESS
DOOR
DOOR
LATCH
LATCH
.
.
(and center of case where appropriate)
CASE
CASE
MOUNTING
MOUNTING
BRACKETS
BRACKETS
(and center of