Draper 220V Access Instrukcja instalacji i obsługi - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Ekran projekcyjny Draper 220V Access. Draper 220V Access 4 stron. Electric projection screen
Drukuj stronę
220V Access by Draper
17.8
cm
16.8
cm
5.4
slot
Engagement bracket (one on each end
of the bottom access panel) clicks into
place with the ball detent on each endcap
120mm
30mm
54mm
Limit Adjustments (Built-in Low Voltage Motors)
Please note: When ordering a motor with built-in Low Voltage Control-
ler, if the case ships separate from the "guts," the case includes the 25'
cable and special low voltage switch.
① Connect the ILT switch to the
motor via the terminal blocks,
or via the modular port using
four conductor modular cable.
When using modular cable,
the cable connectors MUST
NOT be crimped in reverse, as
with standard telephone
cable. (For Dry Contacts Wir-
ing Diagram, see page 4.)
② Set the slide switch to the
lower position. Press and hold
the DOWN button on the
switch to move the viewing
surface to the desired lower
limit. If the screen moves in
the opposite direction, release
the DOWN button and press and hold
down the STOP button for four seconds.
This will reverse the operation of the UP
and DOWN switches.
③ Move slider switch into center position.
Wait a couple of seconds.
Please Note: If you move the slider switch from down to up in one mo-
tion it sets the two limits in the same postion.
④ Set the slide switch to the higher position. Move the viewing surface to the
desired upper limit by pressing and holding the UP button on the wall
switch.
⑤ Return the slide switch to the center position to return to normal operation.
⑥ To set the viewing surface to an alternate format position, move the viewing
surface to the desired position and press the STOP button. Press and hold
the STOP button for at least three seconds to record the position.
Please Note: Pressing and releasing the UP button on the switch will move
the screen to its upper limit. Pressing and releasing the DOWN button will
move the screen to its lower limit.
While the motor is in motion, pressing the STOP button for less than two
seconds will stop the viewing surface at its present position.
Once the motor is stopped, pressing the STOP button will move the view-
ing surface to its alternate format position.
Pressing and holding the STOP button, when the motor is at rest or in mo-
tion, for at least three seconds will record a new alternate format position.
Case Dimensions
22.9
cm
2.6
2.3
cm
cm
2.3
cm
L
20.3 cm
Access
L
Series E 17.8 cm
Series V Varies
+
U
D
C
5V
p
o
o
DC
w
m
n
m
o
n
P
O
T
S
P
O
T
S
P
O
T
S
Slide
Switch
Back View
POSITION
FUNCTION
Set LOWER limit
DOWN
Set UPPER limit
UP
Normal Operation
CENTER
www.draperinc.com
Mounting brackets slide
left and right as needed.
Series E or M
Wiring Diagrams—220V Standard and Quiet Motor
Please Note: Do not wire motors in parallel.
Single Station Control
CE Approved
Junction box at
left end of screen
Internal Screen Wiring
Blue-220v (Common)
Brown-220v (Down)
Black-220v (Up)
To Motor
with
Built-In
Low Voltage
Control
switch
Dashed wiring
by installer
To Motor
with
Wiring Diagrams—220V Motor
Built-In
Low Voltage
with Built-in Low Voltage Controller
Single Low Voltage Control
Dashed wiring
by electrician
Wall Switch,
RF or IR
Receiver,
or integrated
control system
To 220V Line
*These wiring diagrams are for Access screens with motor on audience
left (standard), and fabric unrolling from the back of the roller (standard).
(765) 987-7999
Mount ing
hard ware
supplied by
others
Series V
Multiple Station Control
Junction box at
left end of screen
Green/Yellow (Motor Ground)
Red
Red
Red
220v,
50 Hz.
220v, 50 Hz.
Multiple Low Voltage Controls
Dashed wiring
by electrician
Data Cable
To 220V Line
page 3 of 4
Not CE Approved
Internal Screen Wiring
Blue-220v (Common)
Brown-220v (Down)
Black-220v (Up)
Green/Yellow (Motor Ground)
Cap off with wire
nut & tape
Blue
Black
Blue
Black
Blue
Black
Dashed wiring
by installer
Data
Cables
Wall Switches,
RF or IR
Receivers,
or integrated
control systems