Draper Luma 2 Instalacja i obsługa - Strona 2

Przeglądaj online lub pobierz pdf Instalacja i obsługa dla Ekran projekcyjny Draper Luma 2. Draper Luma 2 4 stron. Heavy duty spring roller operated projection screen
Również dla Draper Luma 2: Specyfikacje (1 strony), Broszura (16 strony)

Drukuj stronę
Draper Luma 2 Instalacja i obsługa
Luma 2
PLEASE READ - Safety Information
Important Safety Information
Improper installation and use of the Luma 2 Projection Screen can result in serious injury or death. Primarily, injuries can occur if the unit falls due to imprecise
installation, mishandling of the unit during installation, or installation on an insufficient wall or ceiling structure. Please use extreme care.
1. Please read the following installation guidelines thoroughly and follow them
carefully. Failure to do so may cause product to fall or otherwise fail, and could
result in serious injury.
2. Installation and calibration of the unit should only be performed by an authorized,
qualified, and experienced professional.
3. Do not affix the unit to walls or ceilings that have inadequate strength to
permanently hold the unit during use. It is the owner's and installer's responsibility
to confirm the wall or ceiling to which the unit attaches is sufficient to permanently
hold the weight and stress loads of the unit at all times. Draper
responsible for improper installation, application, testing, or workmanship related
to the product at place of installation.
4. It is the installer's responsibility to make sure appropriate fasteners are used for
mounting.
5. All hardware must be installed level. Unit must be level and square.
6. Never leave the area while operating the unit during installation, maintenance, or
normal operation, unless it is secure and safe.
7. Before testing or operation, carefully inspect the entire area and path
of unit to be sure no persons or objects are in the area.
underneath)
1. Look for any job site conditions that could interfere with installation or operation of
the system.
2. Read carefully and be sure to understand all installation instructions and all
related operations manuals. These instructions are intended to serve as a guide
for the installer and owner. They should be followed closely and combined with the
expertise of experienced qualified installers. Draper, Inc., is not responsible for
improper installation, application, testing, or workmanship related to the product at
place of installation. Please retain all instructions for future use.
Section 2 - Operation
To lower viewing surface
1. Grasp center of dowel and pull down.
2. Hesitate, then allow screen to retract very slowly until it locks in place.
To raise viewing surface
1. Pull the screen down and, if fully down, slightly outward
2. Give screen a quick "flick" and allow screen to retract quickly, but control retraction so screen does not collide into case.
Please Note: If the surface stops between the full up or full down positions, it will not retract completely back into the
case. Lower viewing surface to the full down position and then let it completely retract back into the case without
stopping or slowing it down.
AutoReturn
To lower viewing surface
1. Grasp center of dowel and pull down.
2. Hesitate, then allow screen to retract very slowly until it locks in place.
To raise viewing surface
1. Pull down gently until viewing surface stops.
2. Release viewing surface.
WARNING
8. During testing or operation, carefully watch the surrounding area for any potential
safety concerns including nearby persons or objects.
11. After installation, the entire system, including all sensors, should be carefully tested
to ensure safe and normal operation. Extreme care should be taken during testing
to remain clear of moving parts to avoid possible injury.
12. Operation of unit should be performed only by authorized and qualified personnel,
who have been trained in its safe and effective operation and understand its safety
features.
, Inc., is not
®
13. The safety features of the unit should never be disabled, bypassed, or overridden.
The system should not be operated until all safety features are properly and
completely installed, calibrated, and tested.
14. Unit may need to comply with local, state, or district rules and regulations, in
particular when installed in schools. All applicable rules and regulations should be
reviewed before installation and use.
15. Failure to precisely follow installation guidelines invalidates all warranties.
16. Custom products/installations may not be reflected in this manual. Call Draper, Inc.,
if you have questions about the installation of custom products or any questions
(especially
about your installation.
Before Beginning Installation
3. Open cartons lengthwise.
4. Locate and lay out all pieces.
5. Inspect all boxes to make sure you have received the proper unit and parts.
Controls may be shipped separately, or in same carton as unit.
6. If you have any difficulties with installing, servicing, or operating your unit, call your
dealer or Draper, Inc., 765-987-7999.
.
(20 degree angle)
page 2 of 4
Important Safety Information