Draper Premier Instrukcja instalacji i obsługi

Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Ekran projekcyjny Draper Premier. Draper Premier 2 stron. 220v premier electric projection screen
Również dla Draper Premier: Instrukcja instalacji i obsługi (2 strony), Instrukcje instalacji (2 strony), Instrukcje instalacji i obsługi (7 strony), Instrukcje instalacji (4 strony), Instrukcje instalacji (2 strony), Instrukcje instalacji (2 strony), Instrukcja instalacji i obsługi (4 strony), Instrukcja instalacji i obsługi (7 strony)

Drukuj stronę

Draper Premier Instrukcja instalacji i obsługi

Targa and Premier 220V Electric Projection Screen—Large Sizes by Draper

These Installation/Operating Instructions are available in the ofﬁ cial language of the

country where you purchase the product. Please contact your distributor to request a

copy.

Vous pourriez demander les instructions d'installation et d'opération traduises dans

la langue ofﬁ cielle du pays ou vous achetez le produit. Veuillez demander à votre

distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der ofﬁ ziellen

Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen Sie die

jeweilige Verkaufs-Abteilung.

➀ Read instructions through completely before proceeding.

➁ Follow instructions carefully. Installation con trary to instructions in val i dates war-

ranty.

➂ Screen should be accessible for complete removal should fabric be come dam-

aged or should other ser vice be required.

➃ Screen should be installed level (using a carpenter's level). The case must also

be installed so that the top of the case is level (front-to-back) to prevent the fabric

from contacting the case housing.

➄ Nothing should be fastened to screen dowel or viewing surface.

➅ Operating switch(es) packed separately in screen carton. Do not dis card with

packing material.

➆ Screen operates on 220V AC, 50 Hz., 1 ph. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any re spon si bil i ty on the

part of Draper, Inc. for improper in stal la tion or faulty work man ship at the jobsite.

Hanging Screen

General:

Screen should be lifted into position only by the end mounting brackets.

Never attempt to lift screen along its length.

Installer must also insure that wall or ceiling structure is of adequate strength.

Supporting hardware must be essentially vertical. Do not suspend this product using

chain or cable (see note at bottom right regarding this screen with Tork Star).

The screen must be securely fastened using at least two of the mounting holes

provided in each of the case mounting brackets.

When locating view ing surface and checking clear ance for screen's op er a tion,

remember surface is centered in case. Handle case care ful ly to protect its ﬁ nish.

Regardless of mounting method, screen should be positively and securely sup port ed

so that vibration or even abusive pulling on the viewing surface will not cause case to

work loose or fall. Installer must insure that fas ten ers used are of adequate strength and

suit able for the mounting sur face cho sen.

Ceiling Installation:

Product is very heavy: Installer must provide adequate attachment hardware and

anchors as required. Installer must also insure that ceiling structure is of adequate

strength.

Wall Installation:

Product is very heavy: Installer must provide adequate attachment hardware

and anchors as required. Installer must also insure that wall structure is of

adequate strength.

Caution: Do not remove the roller as-

sembly from the case unless necessary for

repairs. If the roller assembly is removed,

be sure motor is fully re-seated in the

bracket, and re-secure it carefully with

the motor retaining spring and screw (see

diagram below).

Screw is included with Large

Targas and Large Premiers.

Please note: Do not use a power screwdriver to tighten screw. Maximum torque for

tightening screw is 5 lb-inches.

Electrical Connections

Screen operates on 220V AC, 50 Hz., 1 ph. current.

Junction box is located inside left endcap and cover plate is secured to endcap with two

screws. Junction box contains terminal strip, per wiring diagram on reverse.

Screen is shipped with internal wiring complete and control switch(es) fully boxed. Wire

connecting screen to switch(es) and switch(es) to power supply should be furnished by

installer. Connections should be made in accordance with wiring diagram supplied, and

wiring should comply with na tion al and local electrical codes.

All operating switches should be "Off" before power is con nect ed.

Installation/Operating Instructions

Caution

Printed in U.S.A.

Before fully operating screen: On Large Targa, remove tape; on Large Premier, lower

viewing surface enough to fully expose shipping brackets, then remove shipping brackets

by loosening screws, removing end shipping brackets, sliding center shipping brackets off

dowel, and re-tightening screws (see diagram).

220V AC Single Station Control—3-position up-off-down switch per mits op er a tion to be

stopped at any point. Factory adjusted limit switches au to mat i cal ly stop screen when fully

down or fully up.

220V AC Multiple Station Control—Switches are sim i lar in ap pear ance to 220V Single

Station Control. Screen stops when switch is re leased and may be re start ed in either

direction. Factory adjusted limit switch es stop screen automatically when fully up or fully

down.

24V Control—Three-button up-stop-down switch(es) stop at any point de sired, operate

in any sequence. Factory adjusted limit switches au to mat i cal ly stop screen when fully up

or fully down. Installer should incorporate an all-pole disconnect in the ﬁ xed wiring.

Key Operated Switching—Two kinds of key-op er at ed switches are op tion al ly available

with this unit. ➀ The key-operated power sup ply switch controls power to the screen and

switch es. When it is "off", the switches will not operate screen. Key may be removed from

the switch in either "on" or "off" position. ➁ A three-po si tion key switch per mits the screen

to be operated directly by key. In this case, the screen's operator must always have a key.

RS232/Ethernet—Serial communication and network communication optionally available

with wall switches, RF or IR remote.

Screen has been factory set and should not nor mal ly require further ad just ment. How-

ever, if you desire to change the "up" and "down" stop ping po si tions, proceed as follows:

CAUTION: Be sure all switches are in "off " position before ad just ing limit switches.

Always be pre pared to shut screen off man u al ly when new adjust- ment is being tested.

Screen may be se vere ly dam aged if viewing surface is al lowed to run too far up or too far

down.

Adjusting "fully up" position — "Up" stopping position may be ad just ed by turning the

yellow limit switch adjustment socket. The yellow socket is lo cat ed on left end of screen

roller and is accessible to a screwdriver/Allen wrench (4mm or

coun ter clock wise will allow the view ing surface to retract farther into the case. Turn ing it

clockwise will cause the sur face to stop farther out of the case. One full revolution of the

socket will alter the stop ping position of the view ing surface by ap prox i mate ly 1½".

Adjusting "fully down" position — "Down" stopping position may be adjusted by turn-

ing the white limit switch adjustment socket. The white socket is located on the left end

of screen roller and is accessible to a screw driv er/Allen wrench (4mm or

the socket coun ter clock wise will allow the viewing surface to run farther down. Turning it

clockwise will shorten the viewing surface, causing it to stop in a less extended po si tion.

At no time should viewing surface be unrolled enough to expose any part of screen roller.

16.8

Targa

Use of Large Case Targa or Large Case Premier screens with TorkStar Utility Li-

neset requires specially modiﬁ ed Large Premier or Large Targa case and mount-

ing brackets. DO NOT use TorkStar with standard Large Case Targa or Premier

screen and brackets. Contact Draper for details.

If you encounter any difﬁ culties installing or ser vic ing your large size Targa or Premier screen,

call your dealer or Draper Inc., Spiceland, Indiana, USA, (765) 987-7999 or fax (765) 987-1689.

Operation

Adjustments

"). Turn ing the socket

16.8

Premier

IMPORTANT

"). Turning