Draper SLX14 Instrukcja instalacji i obsługi - Strona 2
Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Ekran projekcyjny Draper SLX14. Draper SLX14 7 stron. 230v ac scissor lift slx video projector lift
Również dla Draper SLX14: Broszura i specyfikacje (16 strony), Instrukcja instalacji i obsługi (7 strony), Instrukcja instalacji i obsługi (8 strony), Instrukcja instalacji i obsługi (4 strony), Instrukcja instalacji i obsługi (7 strony)
Drukuj stronę
Scissor Lift SLX by Draper
Installing Projector
Generally, the video pro jec tor should be sus pend ed from the Projector
Pan ac cord ing to pro jec tor man u fac tur er's in struc tions and rec om mend ed
stan dard ceiling mounting hardware.
The Scissor Lift SLX has a grounded 110-120V AC, 60 Hz power cord for
pro jec tor power supply. The power cord is laced down the back scissor and is
"hot" at all times.
Control cables should be laced through our Cable Management System.
Make sure to use fl exible cables, and to allow enough cable at each turn
so cables do not stretch or kink. This will ensure that cords do not become
tangled and dam aged during Scissor Lift SLX operation.
Unit and projection system should be operated, checked and ad just ed as
necessary at this time.
NOTE: Immediately upon completion of the surrounding ceiling, units should
be operated to confi rm that optional ceiling closure panel stops just short of
touching ceiling in closed position.
Warning: Keep fi ngers and other objects away from automatic ceiling
closure and scissor mechanisms when unit is operating. Serious injury or
damage could result.
Lifting Cable Bar
Installing Optional Universal Projector Mount
If you ordered the unit with optional Universal Projector Mount pre-installed,
disregard these instructions.
If you did not order the mount pre-installed, you will need to install a new
Projector Pan, which includes the Universal Projector Mount's rectangular
plate.
① Lower unit until the Bottom Pan is resting on a tabletop or other stable and
sturdy surface.
② Remove Lifting Cable Bar from Bottom Pan (see Fig. 2).
③ Remove bolts holding Projector Pan to Bottom Pan (see Fig. 2).
④ Remove Projector Pan and set aside.
⑤ Place new Projector Pan with Universal Mount into place.
⑥ Re-attach Projector Pan to Bottom Pan.
⑦ Re-attach Lifting Cable Bar to Bottom Pan.
The Projector Pan can be moved forward or back.
① Make sure Bottom Pan is supported.
② Remove the Lifting Cable Bar (see Fig. 2).
③ Remove screws holding Projector Pan on Bottom Pan (see Fig. 2).
④ Move Bottom Pan forward or back.
⑤ Replace screws.
⑥ Replace Lifting Cable Bar.
Run the unit to its "Service" position and make sure pan is level. Try and set
so that pan is not more than ¾" out of level. However, the pan does not
have to be perfectly level, as long as the positioning is consistent and
repeatable in "Show" and "Closed" positions.
① Make sure Bottom Pan is supported.
② Remove screws holding Lifting Cable Bar to the Bottom Pan (see Fig. 2).
③ Move Lifting Cable Bar forward or back (see Fig. 2).
④ Replace screws.
⑤ Check level again. If still not level, repeat.
Attachment points
for Lifting Cables
¼"-20 x ¾" hex head
cap screws for attaching
Projector Pan to Bottom Pan
Figure 2
www.draperinc.com
(765) 987-7999
Adjusting for Level or Center of Gravity
Preferred Method—Adjusting Projector Pan
Secondary Method—Adjusting Lifting Cable Bar
(if above does not work)
15
3
/
"
16
12"
Figure 3
page 2 of 7
3
/
"-18 x 1" hex head cap
8
screws for attaching Lifting
Cable Bar to Bottom Pan
7"
1
2
/
"
16