Bosch WAE22464AU Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Spryskiwacz Bosch WAE22464AU. Bosch WAE22464AU 8 stron. Front load washing machine

Bosch WAE22464AU Instrukcja obsługi
Safety instructions
Care
– Read the instruction manual and installation instructions and all other information enclosed with the washing
machine and act accordingly.
– Retain the documents for subsequent use.
Risk of electric shock
– Never pull the cable to disconnect the mains plug.
– Never insert/disconnect the mains plug with damp hands.
Danger to life
For worn-out appliances:
– Disconnect the mains plug.
– Sever the mains cable and discard along with the plug.
– Destroy the lock on the washing machine door. This will prevent children from
locking themselves in and risking their lives.
Danger of suffocation
– Keep packaging, film and packaging parts out of the reach of children.
Risk of poisoning
– Keep detergents and care products out of the reach of children.
Risk of explosion
– Items of laundry pretreated with cleaning agents containing solvents, e.g. stain
remover / cleaning solvent may lead to an explosion after being loaded into the
washing machine.
1. Pull the drawer out, press down the insert and fully remove the drawer
Rinse items of laundry thoroughly by hand beforehand.
Risk of injury
– The washing machine door can become very hot.
2. To remove the insert: press the insert upwards from below with your
– Be careful when draining hot detergent solution.
3. Clean the detergent dispenser tray and insert with water and a brush and
– Do not climb onto the washing machine.
– Do not lean on the open washing machine door.
– Do not reach into the drum if it is still rotating.
4. Attach the insert and engage (connect the cylinder to the guide pin).
– Be careful when opening the detergent drawer while the machine is in operation.
5. Push in the detergent drawer.
Consumption values
Additional
Electricity
Programme
Programme
Load
Water**
function
consumption**
duration**
Cottons 40 °C
-
7 kg
0,48 kWh
68 l
2 h
Cottons 40 °C*
Intensive*
7 kg
0,73 kWh
72 l
4 h
Cottons 60 °C
-
7 kg
0,98 kWh
73 l
1 ¾
h
Cottons 60 °C
Intensive
7 kg
1,14 kWh
73 l
2 ½
h
Cottons 90 °C
-
7 kg
2,02 kWh
79 l
2 h
Cottons 90 °C
Intensive
7 kg
2,13 kWh
79 l
2
¾
h
Information on the display panel
Easy-Care 40 °C
-
3 kg
0,54 kWh
40 l
1 h
F: 16
Mixed Load 30 °C
-
3 kg
0,32 kWh
35 l
¾
h
F: 17
Delicate/Silk 30 °C
-
2 kg
0,25 kWh
38 l
¾
h
F: 18
/
Wool 30 °C
-
2 kg
0,15 kWh
34 l
¾
h
* Programme setting with maximum spin speed for testing according to or in accordance with AS/NZS 2040.2
and AS/NZS 6400.
F: 21
Note on comparative tests: test the test programme with maximum load,
Intensive additional function selected, max-
F: 23
imum spin speed.
A short programme which can be used for coloured items is
Easy-Care 40 °C, without the
Intensive additional
function selected and set to maximum spin speed.
** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient
temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected
additional functions.
8
7
– Risk of electric shock.
Maintenance
Disconnect the mains plug.
– Risk of explosion. No solvents.
Before washing for the first time
Detergent solution pump
Do not load any laundry into the machine. Turn on the tap.
Turn the programme selector to Off and disconnect the mains plug.
Add the following to compartment II:
1. Open and remove the service flap.
– approx. 1 litre water
– detergent (dosage according to the manufacturer's instructions for light soiling and the
appropriate degree of water hardness)
Set the programme selector to
Easy-Care 60 °C and select
Start/Pause. At the end of
2. For models with a drainage hose: Remove the drainage hose from
the programme, turn the programme selector to Off.
the retainer and pull it from the housing.Remove the container.
Remove the sealing cap, allow the detergent solution to flow out.
Machine housing, control panel
Replace the sealing cap and place the drainage hose in the retainer.
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
2* For models without a drainage hose: Carefully unscrew the pump cover
– Remove detergent and cleaning agent residue immediately.
until the detergent solution begins to flow out.When the service flap is half
– Do not clean with a jet of water.
full, close the pump cover and empty the service flap. Repeat the above
steps until all the detergent solution has completely drained out.
Cleaning the detergent drawer and housing...
3. Carefully unscrew the pump cover (residual water).
... if it contains detergent or fabric softener residues.
4. Clean the interior, pump cover thread and pump housing (the impeller in
the detergent solution pump must rotate).
from the housing.
5. Replace the pump cover and screw it tightly.
finger.
6. Place the service flap back on and close.
dry it. Also remove any detergent or fabric softener residues in the
housing.
To prevent unused detergent from flowing straight into the drain during the next wash:
Pour 1 litre of water into compartment II and start the
Leave the detergent drawer open so that any residual water can
Drainage hose at the siphon
evaporate.
Turn the programme selector to Off and disconnect the mains plug.
Washing drum and rubber seal
1. Loosen the hose clamp, carefully remove the drainage hose (residual
Wipe the inside of the rubber seal dry with a cloth. Leave the washing machine door open so
water).
that the drum can dry out. Rust stains - use chlorine-free cleaning agent, not steel wool.
2. Clean the drainage hose and siphon connecting piece.
3. Reattach the drainage hose and secure the connection with the hose
Descaling
Ensure there is no laundry in the machine
clamp.
Descale the appliance according to the descaler manufacturer's instructions. This should not
be necessary if the correct dosage of detergent is used.
Filter in the water supply
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (apart from
3. Choose
Start/Pause. Let the programme run for approximately
depending on model
40 seconds.
Close the washing machine door properly; laundry may be caught.
4. Turn the programme selector to Off. Disconnect the mains plug.
Open the tap completely, supply hose kinked or trapped;
Clean the filter:
Clean the filter
page 10, Water pressure too low.
Detergent solution pump blocked; Clean the detergent solution pump
page 10.
1. Depending on model:
Drainage hose / waste pipe blocked; Clean the drainage hose at the siphon
page 10.
Disconnect the hose from the tap.
Clean the filter using a small brush.
Motor fault. Call customer services.
Water in the base tub, appliance leaking. Call customer services.
and/or for Standard and Aqua-Secure models:
Remove the hose on the rear of the appliance,
Remove the filter with pliers and clean.
2. Connect the hose and check for leaks.
9
– Risk of scalding. Allow the
What to do if ...
detergent solution to cool down.
– Turn off the tap.
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
No water supply.
Start/Pause not selected?
Detergent not dispensed.
– Tap not turned on?
– Filter blocked? Clean the filter
– Supply hose kinked or trapped?
Washing machine door cannot
– Safety function active. Programme stopped?
be opened.
(without final spin) selected?
– Can be opened by emergency release only?
Programme does not start.
Start/Pause or
Ready in time selected?
– Washing machine door closed?
– Childproof lock active? Deactivate
Detergent solution is not
(without final spin) selected?
drained.
– Clean the detergent solution pump
– Clean the waste pipe and/or drainage hose.
Water not visible in the drum.
– Not a fault - water below the visible area.
Unsatisfactory spin result.
– Not a fault - the unbalanced-load detection system has cancelled the spin cycle
Laundry wet/too damp.
because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the drum.
– Selected speed too low?
The programme duration
– Not a fault – the programme sequence is optimised for the particular wash
changes during the wash cycle.
process. This may result in changes to the programme duration in the display
field.
Drain programme.
Spin cycle performed several
– Not a fault - unbalanced load detection system adjusts the imbalance.
times.
Residual water in the
– Not a fault - the action of the care product is not affected.
compartment for care
– Clean the insert if necessary
products.
Odour formation in the washing
– Run programme
Cottons 90 °C without laundry. Use standard detergent.
machine.
Status display
(Wash)
– Too much detergent used? Mix 1 tablespoon of fabric softener with ½ litre of
flashes. Foam may be coming
water and pour into dispenser II (not for outdoor and down-filled textiles!).
out of the detergent drawer.
– Reduce the detergent dosage for the next wash cycle.
Intense noise formation,
– Are the appliance feet fixed?
vibrations and "wandering"
Secure the appliance feet
Spin /
Drain).
during the spin cycle.
– Transportation safety devices removed?
Remove the transportation safety devices
Noises during spin and drain
– Clean detergent-solution pump
cycles.
Display panel/indicator lamps
– Power cut?
do not function during
– Fuses triggered? Reset/change the fuse.
operation.
– If the fault occurs repeatedly, call customer services.
Programme sequence longer
– Not a fault - unbalanced load detection system adjusts imbalance by repeatedly
than usual.
distributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse cycle.
Detergent residues on the
– Occasionally, phosphate-free detergents contain water-insoluble residues.
– Use the
Rinse/Freshen Up or brush out the laundry after washing.
laundry.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call customer services
Installation instructions.
10
page 10.
page 4.
page 3, 4.
page 9.
page 5.
page 3, 4.
page 10.
page 5.
page 9.
Installation instructions.
Washing machine
Installation instructions.
WAE22464AU ...
page 10.
en operating instructions
11