Bosch WAE24162GR/ Series Instrukcja obsługi - Strona 2
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Spryskiwacz Bosch WAE24162GR/ Series. Bosch WAE24162GR/ Series 8 stron.
Drukuj stronę
Safety instructions
Care
– Read the instruction manual and installation instructions and all other information enclosed
with the washing machine and act accordingly.
– Retain the documents for subsequent use.
Risk of electric shock
– Never pull the cable to disconnect the mains plug.
– Never insert/disconnect the mains plug with damp hands.
Danger to life
For worn-out appliances:
– Disconnect the mains plug.
– Sever the mains cable and discard along with the plug.
– Destroy the lock on the washing machine door. This will prevent
children from locking themselves in and risking their lives.
Danger of suffocation
– Keep packaging, film and packaging parts out of the reach of
children.
Risk of poisoning
– Keep detergents and care products out of the reach of children.
Risk of explosion
– Items of laundry pretreated with cleaning agents containing
1. Pull out, press insert down, remove draw completely.
solvents, e.g. stain remover/cleaning solvent may cause an
explosion after being loaded into the washing machine.
2. To remove the insert: press the insert upwards from below with your
Rinse items of laundry thoroughly by hand beforehand.
Risk of injury
– The washing machine door can become very hot.
3. Clean the detergent dispenser tray and insert with water and a brush and
– Be careful when draining hot detergent solution.
– Do not climb onto the washing machine.
4. Attach the insert and engage (connect the cylinder to the guide pin).
– Do not lean on the open washing machine door.
5. Push in the detergent drawer.
– Do not reach into the drum if it is still rotating.
– Be careful when opening the detergent drawer while the machine
is in operation.
Consumption values
Additional
Electricity
Programme
Programme
Load
Water***
function
consumption***
duration***
/
(Cottons cold)
7 kg
0.25 kWh
60 l
2:36 h
/
(Cottons) 40 °C**
7 kg
0.69 kWh
60 l
2:36 h
/
(Cottons) 60 °C**
7 kg
1.33 kWh
60 l
2:39 h
Information on the indicator lights
/
(Cottons) 60 °C*
EcoPerfect
7 kg
1.05 kWh
47 l
3:08 h
A signal sounds and indicator lights for the spin speed flash:
/
(Cottons) 90 °C
7 kg
2.00 kWh
64 l
2:47 h
¤
Close the washing
(Easy-Care) 40 °C**
3 kg
0.55 kWh
55 l
1:17 h
machine door properly;
¤
laundry may be caught.
(Mix) 30 °C
3 kg
0.24 kWh
32 l
1:03 h
¤
¤
2 kg
0.06 kWh
31 l
0:41 h
(Delicate/Silk cold)
¤
(Wool cold)
2 kg
0.10 kWh
39 l
0:40 h
(Wool) 30 °C
2 kg
0.19 kWh
39 l
0:40 h
¤
Motor fault. Call the after-
* Programme setting for testing and energy labelling in accordance with EU directive 92/75/EEC.
sales service.
¤
** Programme setting for testing in accordance with valid standard EN60456.
Note on comparative tests: Try out the test programme by washing the specified load using the maximum spin speed.
¤
As a short programme for coloureds, select the programme
( Mix) 30 °C with the maximum spin speed.
¤
*** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient tem-
¤
perature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional
functions.
8
7
– Risk of electric shock. Disconnect the
Maintenance
mains plug.
– Risk of explosion. No solvents.
Before washing for the first time
Detergent solution pump
Do not put any laundry in the machine. Turn on the tap, add approximately 1 litre of water and
Turn the programme selector to Off and disconnect the mains plug.
then ½ a measuring cup of detergent into compartment II. Turn the programme selector to
(Easy-Care) 60 °C and choose Start/Pause
. At the end of the
1. Open and remove the service flap.
programme, turn the programme selector to Off.
Machine housing, control panel
2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it
– Wipe with a soft, damp cloth.
from the housing. Remove the container.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
Remove the sealing cap, allow the detergent solution to flow out.
– Remove detergent and cleaning agent residue immediately.
Replace the sealing cap and place the drainage hose in the retainer.
– Do not clean with a jet of water.
2* For models without a drainage hose: Carefully unscrew the pump cover until the
Cleaning the detergent drawer ...
detergent solution begins to flow out. When the service flap is half full, close the pump cover
... if it contains detergent or fabric softener residues.
and empty the service flap. Repeat the above steps until all the detergent solution has
completely drained out.
3. Carefully unscrew the pump cover (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent
solution pump must rotate).
finger.
5. Replace the pump cover and screw it tightly in place.
6. Place the service flap back on and close.
dry it.
Leave the detergent drawer open so that any residual water can
To prevent unused detergent from flowing straight into the drain during the next wash: pour 1 litre of water into
compartment II and start the
evaporate.
Drainage hose at the siphon
Drum
Turn the programme selector to Off and disconnect the mains plug.
Leave the washing machine door open so that the drum can dry out.
Rust stains - use chlorine-free cleaning agent, not steel wool.
1. Loosen the hose clamp, carefully remove the drainage hose (residual water).
Descaling
Ensure there is no laundry in the machine
2. Clean the drainage hose and siphon connecting piece.
3. Reattach the drainage hose and secure the connection with the hose clamp.
Descale the appliance according to the descaler manufacturer's instructions. This should not
be necessary if the correct dosage of detergent is used.
Filter in the water supply
Risk of electric shock.
Do not immerse the HydroSafe safety device in water (it contains an electric valve).
model-dependent
Reduce the water pressure in the supply hose:
¤
Detergent solution pump
¤
Open the tap completely,
1. Turn off the tap.
blocked; Clean the
supply hose kinked or
¤
¤
detergent solution pump
trapped;
2. Select any programme (except for
¤
¤
–> page 10.
Clean the filter
3. Select Start/Pause
¤
¤
Drainage hose/waste pipe
–> page 10,
4. Turn the programme selector to Off. Disconnect the mains plug.
¤
¤
blocked; Clean the drainage
Water pressure too low.
Clean the filter:
hose at the siphon
–> page 10.
1. Depending on model:
Disconnect the hose from the tap.
¤
Water in the base tub,
Clean the filter using a small brush.
appliance leaking. Call the
¤
after-sales service.
¤
and/or for Standard and Aqua-Secure models:
¤
Remove the hose on the rear of the appliance.
¤
Remove the filter with pliers and clean.
2. Connect the hose and check for leaks.
9
– Risk of scalding.
Allow the detergent solution to cool down.
What to do if ...
– Turn off the tap.
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
No water supply.
– Start/Pause
Detergent not dispensed.
– Tap not turned on?
– Filter blocked? Clean the filter –> page 10.
– Supply hose kinked or trapped?
Washing machine door
– Safety function active. Wait approx. 2 minutes.
cannot be opened.
– Is X
4.
Programme does not
– Start/Pause
start.
– Washing machine door closed?
Detergent solution is not
– Is X
drained.
4.
– Clean the detergent solution pump –> page 10.
– Clean the waste pipe and/or drainage hose.
Water not visible in the
– Not a fault - water below the visible area.
drum.
Spin result not
– Distribute large and small items of laundry evenly in the drum.
satisfactory.
–
– Too low a speed selected? –> page 5.
Spin cycle performed
– Not a fault - unbalanced load detection system adjusts the
several times.
imbalance.
Residual water in the
– Not a fault - the action of the care product is not affected.
(Empty) programme.
compartment for care
– Clean the insert if necessary –> page 9.
products.
Odour formation in the
– Run programme
washing machine.
laundry. Use standard detergent.
Foam escaping from the
– Too much detergent used?
detergent drawer.
If foam is escaping from the detergent drawer:
Mix 1 tablespoon of fabric softener with ½ litre of water and pour
into compartment II (not with outdoor or down fabrics).
– Reduce the detergent dosage for the next wash cycle.
Intense noise formation,
– Are the appliance feet fixed?
vibrations and "walking"
Secure the appliance feet –> Installation instructions.
during the spin cycle.
– Transportation safety devices removed?
Remove the transportation safety devices –> Installation
instructions.
The indicator lights do
– Power cut?
/
/
(Rinse/Spin/Empty)).
not function during
– Fuses tripped? Reset/change the fuse.
. Let the programme run for approximately 40 seconds.
operation.
– If the fault occurs repeatedly, call the after-sales service.
Programme sequence
– Not a fault - unbalanced load detection system adjusts
longer than usual.
imbalance by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional
rinse cycle.
Detergent residues on
– Occasionally, phosphate-free detergents contain water-insoluble
the laundry.
residues.
– Select
after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service –> Installation instructions.
10
not selected?
(Rinse Hold, without final spin) selected? –> page 3,
selected?
(Rinse Hold, without final spin) selected? –> page 3,
(Easy-Iron) selected? –> page 5.
Washing machine
/
(Cottons) 90 °C without
Instruction manual
Observe the safety instructions on page 8.
/
(Rinse /Spin) or brush out the laundry
Read these instructions and the separate installation instructions before
operating the washing machine.
11
en