Draper Targa Instrukcja instalacji i obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Ekran projekcyjny Draper Targa. Draper Targa 2 stron. Electrically operated projection screen with motor-in-roller
Również dla Draper Targa: Instrukcja instalacji i obsługi (4 strony), Instrukcja instalacji i obsługi (2 strony), Instrukcja instalacji i obsługi (2 strony), Instrukcja instalacji i obsługi (2 strony), Instrukcja instalacji i obsługi (4 strony), Instrukcja instalacji i obsługi (2 strony), Instrukcja instalacji i obsługi (3 strony), Instrukcja instalacji i obsługi (4 strony), Instrukcja instalacji i obsługi (2 strony), Instrukcja obsługi (8 strony)

Drukuj stronę
Draper Targa Instrukcja instalacji i obsługi
Targa 220V Instructions
Wall Mounted
Appropriate hardware
provided by installer.
Methods of Installation
Fasteners for
Crimp
wall mounting
both
by others.
ends
7
/
" hole for
8
electrical
connection.
Optional Ceiling Opening Trim Kit
(Dims-Side View)
203
mm
54 mm
102 mm
162 mm
Program LED
Fuse
MC1
Case Dimensions/Installation Diagrams
Suspended
Appropriate hardware
provided by installer.
Single Station Control
S Hooks for
suspended
installation
by others.
67
mm
1.6
mm
MC1
Red-to Screen (directional)
Black-to Screen (directional)
Blue-Common
Brown-Hot to 230V AC
Green/Yellow-Ground
Low Voltage Wiring by others
AC Wiring by electrician
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
Eye Port for IR Eye. For RF Receiver
or LED Wall Switch, a Splitter and a
Power Supply is required. Plug RF
Receiver or LED Wall Switch and
Power Supply into splitter, then run
cable from Splitter to MC1 Eye Port.
www.draperinc.com
134mm
59mm
150mm
22mm dia.
electrical
connection
hole
220V Wiring Diagrams
Multiple Station Control
CE Approved
Terminal strip in
junction box at left
end of screen
Control
switch
Dashed wiring
by electrician
230V,
PE
50 Hz.
Low Voltage & Remote Control (LVC-III)
Red-to screen (directional)
Brown-to screen (directional)
White-Common to screen, 230V AC
Black-to 230V AC
Yellow-to 230V AC
Green-Ground
Eye Port for IR Eye, RF Receiver or LED
Switch For more than one of these,
a splitter is required.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Aux Port for connecting additional
LVC-III modules (up to six total-
connect from Aux to Eye).
Terminal strip in
junction box at left
end of screen
All-Pole Disconnect
by Others
STOP
STOP
230V, 50 Hz.
Control
Switches
24v DC
(765) 987-7999
Fabric width + 192mm
Viewing
96mm
surface
Not CE Approved
Terminal strip in
junction box at left
end of screen
Cap off with wire
nut & tape
Blue
Red
Black
Blue
Red
Black
Red
Blue
Black
Dashed wiring
by electrician
230V, 50 Hz.
Dashed wiring by electrician
Low voltage wiring by others
All-Pole Disconnect
by Others
STOP
STOP
230V, 50 Hz.
Control
Switches
24v DC
See separate Serial Communication-
RS232 Instruction sheet for enabling
RS232 with the MC1.
Page 2 of 2
Terminal strip in
junction box at left
end of screen