AirStage ASUB30TLAV1 Instrukcja instalacji - Strona 14

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Klimatyzator AirStage ASUB30TLAV1. AirStage ASUB30TLAV1 16 stron.

Drukuj stronę

• Indoor unit address example

(Example) ADDRESS : 24

OPERATION indicator

lamp (Green)

OFF

TIMER indicator lamp

0.5s 0.5s 0.5s 0.5s

(Orange)

OFF

FILTER indicator lamp

0.5s 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s

(Red)

OFF

• Refrigerant address example

(Example) ADDRESS : 30

OPERATION indicator

1.0s

lamp (Green)

OFF

TIMER indicator lamp

0.5s 0.5s 0.5s 0.5s 0.5s 0.5s

(Orange)

OFF

FILTER indicator lamp

(Red)

OFF

• Setting details

Function number

For use with a remote controller, set all rotary switches to 0, and refer to "6.1. Setting the

address" for details.

All switches are set to 0 at the factory.

(2) Others

Indication pattern

Indicator Name

OPERATION indicator lamp (Green)

TIMER indicator lamp (Orange)

FILTER indicator lamp (Red)

(Example) Function : 31, Setting number : 2

OPERATION indicator

0.5s

lamp (Green)

OFF

TIMER indicator lamp

0.5s 0.5s

(Orange)

OFF

FILTER indicator lamp

0.5s

(Red)

OFF

7. FINISHING

After checking for gas leaks (refer to the Installation Manual of the outdoor unit), perform

this section.

Install heat insulation around both the large (gas) and small (liquid) pipes. Failure to do

so may cause water leaks.

7.1. Connection pipe, cable and drain hose

Insulate the drain hose, if necessary, to prevent it from freezing.

(1) Insulate between pipes.

• For (A) Rear, (B) Right and (C) Bottom piping, overlap the connection pipe heat insula-

tion and indoor unit pipe heat insulation and bind them with vinyl tape so that there is no

gap.

• For (D) Left bottom piping, (E) Left piping, (F) Center piping and (G) Left rear piping, butt

the connection pipe heat insulation and indoor unit pipe heat insulation together and bind

them with vinyl tape so that there is no gap.

((A) Rear, (B) Right and (C) Bottom piping)

Connection pipe

(heat insulation)

Bind the pipes together so

that there is no gap.

En-13

1 cycle 12 sec

10 sec

8 sec

1 cycle 12 sec

1.0s

9 sec

OFF

Item

Setting number

Indoor unit address

00 to 63

Refrigeration address

00 to 99

Indication pattern

Function number; tens place (0.5s ON/0.5s OFF)

Function number; ones place (0.5s ON/0.5s OFF)

Setting number: (0 to 9) (0.5s ON/0.5s OFF)

1 cycle 12 sec

0.5s

0.5s 0.5s 0.5s

9 sec

11 sec

10 sec

0.5s

CAUTION

Overlap the insulation.

Indoor unit pipe

(heat insulation)

Vinyl tape

(For (D) Left bottom piping, (E) Left piping, (F) Center piping and (G) Left rear piping)

• Wrap the area which accommodates the rear piping housing section with cloth tape.

• Bind the connection cable with vinyl tape.

• Bundle the piping and drain hose together by wrapping them with cloth tape over the

range within which they fit into the rear piping housing section.

Connection pipe

Connection cable (Power supply cable)

1.0s

Connection cable (Transmission and Remote controller cable)

(2) Temporarily fasten the connection cable along the connection pipe with vinyl tape.

(3)

Fasten the connection pipe to the outside wall with a saddle, etc.

(4) Fill the gap between the outside wall pipe hole and the pipe with sealer so that rain

water and wind cannot blow in.

(5) Fasten the drain hose to the outside wall, etc.

Pipe

GOOD

8. FRONT PANEL REMOVAL AND INSTALLATION

8.1. Intake grill removal and installation

Intake grill removal

Open the intake

grille. While gently

pressing the left and

right mounting shafts

of the intake grille

outward "a", remove

the intake grille in

direction of the ar-

row "b".

Press 4 places on the intake grille to close it completely.

4/7/9 model

Cloth tape

Wrap with cloth tape.

(Accessories)

Vinyl tape

Wrap with cloth tape

Pipe

Cloth tape

Drain hose

Saddle*

Wall

PROHIBITED

Drain

hose

Lifted up

Saddle

Intake grill installation

While holding the

grille horizontal, set

the left and right

mounting shafts into

the pillow blocks

at the top of the

panel "c". To latch

each shaft properly,

insert the shaft until

it snaps.

30/36

model

Indoor unit pipe

Pipe

Outside wall cap*

Sealer putty*

(Outdoors)

*Locally purchased

Wave

End in water