Draper Battery Powered FlexShade Instrukcje instalacji - Strona 3
Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Wyposażenie wnętrz Draper Battery Powered FlexShade. Draper Battery Powered FlexShade 3 stron.
Drukuj stronę
Battery Powered FlexShades by Draper
Solar Rechargeable Battery Instructions
Refer to the instructions on this page if you are using the optional solar
charging kit for the Battery Powered FlexShade.
Solar Panel dims: 11
/
"
7
8
x 1
/
" x
/
" (301mm) x
5
7
8
16
(40mm) x (11mm)
Solar
Panel
Determine Location of Solar Panel
The solar panel must always be installed indoors, directly against the
window glass to allow as much natural light as possible to reach the panel.
Caution! Never install the solar panel on any window glass allowing less
than 65% light transmission (including Low E glass and/or window tinting), or
obstructed by a window pane or bug screen.
Always leave the photovoltaic cells unobstructed.
The three components which make up the Solar Pack must be installed on
the same side as the motor.
Install so that all components may be connected to the wire harness easily,
and that the wire harness does not interfere with the free movement of the
interior window covering.
The solar panel and battery must be mounted outside the headbox or
footprint of the shade, to allow unobstructed operation of the shade.
Solar panel
in bezel shown
taped to window
part of C041.029
Solar Pack
Optional C002.1023
Solar Panel Bracket
Kit sold separately.
Mounting the Solar Panel
Caution! It is imperative that window hardware or framing does not collide
with the solar panel!
Be careful to not damage the wire harness cables during installation.
If adhering the solar panel directly onto the window glass, determine the
position of the solar panel prior to application of 2-sided tape to insure proper
adhesion the first time.
Glass Mounting
Caution: To insure a secure adhesive hold over a long period, prepare the
inside window glass prior to mounting the solar panel. The VHB adhesive tape
should never be touched directly with fingers or other contaminates prior to
adhesion.
1 Clean solar panel bezel corners and window area with alcohol prep pad.
Let dry for two minutes.
2 On a table, with the solar panel facing up, apply the 3M VHB 2-sided tape
to four corners of the solar panel bezel.
Note: The VHB tape is precut for your convenience between the top (facer)
and bottom (backer) liners. With your fingers, lift off each precut adhesive
piece so that it remains attached to the "facer" material. The opposite side of
the tape should then be released from the back liner.
3 Remove the "facers" of the applied VHB tape. Position the bezel with solar
panel facing to outdoors , then press entire panel with firm, even pressure
into the glass for 10-15 seconds. The panel is now supported by the adhe-
sive to glass bond but will require 24 hours of cure time to allow full
strength characteristics. Do not disturb during this period.
Solar Panel
Mounting Brackets
Rechargeable
NiMH Battery Tube
part of C041.029
Solar Pack
NiMH Battery
must be fully
charged using
C088.003
Charger Pack
(sold separately)
www.draperinc.com
Mounting Brackets
1 Determine location of brackets. Locate brackets so that solar panel will
be against the window, and outside the headbox or footprint of the shade,
to allow unobstructed operation of the shade.
2 Pre-drill mounting holes.
3 Mount brackets using hardware (not included) appropriate for mounting
surface.
4 Attach solar panel in brackets.
5 Continue installation of battery and shade as outline on page 1.
6 Connect solar panel and battery to motor.
1
/
"
7
16
.16"
/
"
5
8
4¼"
¾"
Battery State of Charge
The Battery is shipped from the factory inside the battery tube with a
partial charge only.
Battery Preparation
Have a service professional fully charge the battery using the compatible
Solar Pack Rapid Charger.
Refer to Solar Pack Wall Charger Instructions.
CAUTION! Use of another battery charger is a safety hazard. Disconnect
from AC wall receptacle upon completion of charge.
Battery Tube Install Location
Once conditioned with a pre-charge, the battery tube assembly can be
secured and hidden from view either behind, inside or next to the window
covering product hardware.
CAUTION! If installing the battery vertically, always position it with the
cable output upwards to reduce unrestrained wire from catching the shade.
Connections
CAUTION! The wiring harness connecting the Solar Pack components
must be protected from the movement of the motorized window covering.
CAUTION! Do not change the configuration of this system to include differ-
ent connectors.
1 Connect the wire harness to the motor.
2 Connect the solar panel to the wire harness.
3 Connect the battery tube to the wire harness.
Commissioning
Activation of Motor
If the Solar Pack is being installed as an upgrade to an existing shade
installation, there is no need to reprogram the motor.
If the Solar Pack is being installed with a new motor, follow the motor
installation guide.
Product in Use
Normal Operation
After commissioning, the battery is trickle-charged by electrical energy
generated by the solar panel. The energy is stored in the high capacity NiMH
battery (acting like a reservoir) and the system provides uninterrupted service
through many climatic seasons. It is normal for the battery to gain more en-
ergy in summer as compared to winter—the Solar Panel converts the intensity
of light to energy upon availability.
Excessive Energy Use
CAUTION! If daily motor activations exceed recommended cycles per day
as stated in the Solar Performance Chart, the solar panel will not be able to
"replenish" the battery as designed.
If the motorized shade does not operate due to an excessively diminished
battery, the battery may require a full recharge.
If the battery no longer provides adequate power to operate your motor, a
freshly charged replacement battery may be ordered.
(765) 987-7999
Page 3 of 3
1½"
.16"
.16"
/
/
"
"
5
5
8
8
2
/
"
3
8
/
/
"
"
5
5
/
"
3
8
8
8