Draper Spring-Roller Window Shade Instrukcja instalacji i obsługi

Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Wyposażenie wnętrz Draper Spring-Roller Window Shade. Draper Spring-Roller Window Shade 2 stron.

Drukuj stronę

1 Open carton along length, not at end. DO NOT use a knife to open.

2 Each shade is tagged with the size. If fascia is included, each piece is

marked.

3 Install all Draper window shades level. Check with carpenter's level.

4 Left and right brackets are different; be sure you are installing the proper

brackets in the proper opening.

5 Please read the following installation guidelines thoroughly and follow

them carefully. Failure to do so may cause product to fall or otherwise

fail, and invalidates warranty.

With brackets—

Caution: Before mounting shades, verify measurements on the card

provided with the shade, and ensure the brackets are installed at the correct

width.

10 Mount brackets according to type of installation. Use appropriate fasteners (two

per bracket) for wall, jamb or ceiling (see Fig. 1). The installer is responsible

for selecting mounting hardware appropriate for site conditions.

NOTE: Left and right brackets are different; make sure you're installing the proper

bracket.

2 Insert idler end into right bracket (see Fig. 2).

3 Lower spear on left end of roller into left bracket and rotate into locked position

(see Fig. 3). Note: The notch on the spring roller should be positioned down.

The spring has been pre-tensioned in the factory.

For wall mounting,

place spear in this slot.

For ceiling mounting,

place spear in this slot.

Please Note: If shade fabric is uneven, see "Field Adjustments".

With endcaps—

Caution: Before mounting shades, verify measurements on the card provid-

ed with the shade, and ensure the brackets are installed at the correct width.

4 For installations with fascia, mount endcaps according to type of installation.

Use appropriate fasteners for wall, jamb, or ceiling (see Fig. 4). The installer is

responsible for selecting mounting hardware appropriate for site condi-

tions. Snap end covers onto endcaps.

Installation/Operating Instructions

Spring-Roller Window Shades by Draper

Caution

Figure 1

For wall mounting,

place pin in this hole.

For ceiling

mounting, place

pin in this hole.

Figure 2

Figure 3

Figure 4

5 Install shade using steps 2 and 3 from above (see Fig. 4).

6 Place fascia top lip over top edge of endcaps, then rotate down and snap into

place (see Fig. 5). NOTE: Make sure shade fabric does not retract completely

behind fascia.

Caution: Fascia is not fully seated until it clicks into place on both ends.

Once in place, check for secure fit. If not secure, secure with appropriate

fastener (not included).

Please Note: Small hardware shown. Large hardware will look slightly different, but

install and operate the same way.

STEP 1

Caution: Before mounting shades, verify measurements on the card pro-

vided with the shade, and ensure the unit is installed at the correct width.

1 Snap endcap covers onto endcaps.

2 Place endcaps into back/top portion of wall/ceiling headbox or into pocket

extrusion of pocket headbox. Using pre-drilled holes in endcaps, mark the

headbox for drilling.

3 Drill holes in back or top, depending on whether you will be mounting the

headbox to the wall, ceiling or pocket.

4 Attach endcaps and wall/ceiling headbox back/top or pocket headbox extrusion

to wall, ceiling or pocket using mounting hardware appropriate for site conditions.

5 Install shade (see "With Endcaps" section above).

6 Attach headbox fascia or pocket closure (see Fig. 6 for pocket closure). Surface

Headbox fascia is not fully seated until it clicks into place on both ends.

Once in place, check for secure fit. If not secure, secure with appropriate

fastener (not included).

Surface Headbox (Small Shown)

Please Note: Small hardware shown. Large hardware will look slightly different, but

install and operate the same way.

STEP 1

Figure 6 is continued on page 2, where you will find digrams of the large and

small pocket headbox.

If you encounter any difficulties installing or servicing your Spring-Roller FlexShades, call

your dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999, or fax 765-987-7142.

Square Fascia

Clicks into place

STEP 2

Radius Fascia

Clicks into place

STEP 2

Figure 5

Headbox

Square Fascia

Clicks into place

STEP 2

Radius Fascia

STEP 2

Clicks into place

Figure 6