Draper TopSpin Instrukcje instalacji

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Wyposażenie wnętrz Draper TopSpin. Draper TopSpin 3 stron.

Drukuj stronę

1 Inspect all boxes to make sure you have received the proper parts.

2 Open cartons lengthwise.

3 All hardware must be installed level. Shades must be level and square.

4 Do not wire motors in parallel without written permission from Draper.

5 Please read the following installation guidelines thoroughly and follow

them carefully. Failure to do so may cause product to fall or otherwise

fail, and invalidates warranty.

Mounting Brackets

1 Mark the desired location of Mounting Brackets. A maximum

distance of 40" (1014mm) between brackets is recommended.

2 Attach Mounting Brackets to the mounting surface.

Please Note: It is the

installers responsibility to

make sure appropriate

fasteners are used for

mounting surface.

3 Insert Sliding Bracket

Bolts (1 per bracket) into

the channel on the bottom

of each section of

siderailing (See Fig. 1).

Assembling and Attaching Siderails

The siderails have been marked prior to shipment with a 1 or 2.

1 Seperate the sections by number and arrange for assembly.

2 Beginning with Group 1, insert Siderail Connecting Plate

(see Fig. 2) into the first section of siderail.

SIDERAIL

CONNECTING

PLATE

SLIDING

BRACKET BOLT

MOUNTING SURFACE

Align the pre-drilled holes and attach provided nuts.

4 Slide the next section of siderail over the Connecting Plate,

align the pre-drilled holes and attach the provided nuts.

Continue process until siderail is fully assembled.

5 Repeat for the remaining siderail.

6 Align the Sliding Bracket Bolts with the pre-drilled holes in the

top of the Mounting Brackets and fasten the provided nuts.

Form TopSpin_Inst16

Installation Instructions

TopSpin by Draper

Caution

Figure

S ID E R A IL

B O T TO M O F

SLIDING

BRACKET

BOLT

(1 per bracket)

Figure

O UT SI DE O F SI

DE RA IL

MOUNTING

BRACKET

Printed in U.S.A.

Installing Motor

Motor Bracket End

1 Remove

from

tape

cardboard tube

Remove

Motor

Bracket

Spring

Motor

Bracket

Cardboard Tube

(Cutaway)

2 Thread the

motor cable

through the

cardboard

Thread Motor Cord

and cable exit hole

tube

Through Cardboard Tube

motor bracket

& Motor Bracket

(See Fig.3 Detail).

3 The

is pre-assembled in the

rope

Slide the

over

cardboard tube

the

and transfer the

motor

rope

from

cardboard tube

motor

Remove the

cardboard tube

Replace

(see Fig. 4).

Motor

Bracket

Spring

4 Place the

motor

into the

motor

and

bracket

replace the

motor bracket

spring

Idler End

1 Remove the screws from the

bearingholder

Remove

and

bearingholder

tape

Remove

Screws

Bearing

Holder

Motor

(Idler End)

Cardboard

Tube

Figure

You are now ready to install the roller assembly into the t

If you encounter any difficulties installing or servicing your Solar Control Systems, call

your dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999, or fax 765-987-7142.

and the

(See Fig. 3).

motor bracket spring

Motor

Motor Cord

from Motor

Rope to

Pulley A

and turned around a

siderail

cardboard tube

Slide Cardboard Tube Over

Slide Cardboard Tube over

Motor & Transfer Ropes

Cardboard

Tube

Figure

(see Fig 5.)

from

cardboard tube

2 Slide the

over the

cardboard tube

transfer the

from

rope

cardboard tube

. Remove the

tor

cardboard tube

lease

ote

The idler end will rope placement will

mirror the motor end.

MAKE CERTAIN THAT THE

ROPES ARE NOT CROSSED

3 Place the

idler end of motor

in the

. Re-attach the

holder

bearingholder

pin siderails

Figure

Motor Cord

to Power

Motor

and

motor