Alemlube 220A Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Narzędzia Alemlube 220A. Alemlube 220A 2 stron. Trigger action grease gun

Drukuj stronę

Description

The 220A manufactured in Germany, is a trigger action 400g grease gun capable of delivering up to 1.1g of grease per stroke

at a maximum operating pressure of up to 8,500psi. It comes standard with a 30cm flexible extension & a 4 jaw coupler for those

difficult to get at lubrication points. The 220A has a capacity of 500g when using bulk grease & features a slip-type pressure/

volume adjustment which changes the gun from high pressure to high volume. 4 year warranty as standard.

Specifications

Uses

Grease Pressure

Delivery

Capacity

Operating instructions

There are two ways to fill the gun with grease:

A) 400g Grease Cartridge:

Unscrew the grease barrel from the gun and insert the 400g grease cartridge

by holding the barrel assembly & pulling therod back. Remove cap from

the grease cartridge, insert the cartridge into the barrel & then rescrew

the barrel assembly back onto the gun so that the cartridge sits well

against the follower cup. Once in position, press the clamp down

& push the rod firmly back into the barrel.

Important To Note:

When using the gun with a cartridge, the follower cup must

be folded back. The gun is supplied standard with the follower

cup in this position.

B) Bulk Grease Loading:

Unscrew the grease barrel from the gun head & insert the barrel

into the bulk grease. Suck the grease up into the barrel by pulling

the rod all the way back. When barrel is full with grease, rescrew

the barrel assembly back onto the gun head so that the follower

sits well against the grease. Press the clamp down & push the rod

firmly back into the barrel.

Important To Note:

When using the gun with bulk grease, the follower cup must be folded

forward. To do this, take the follower cup and rod assembly out of the

barrel, fold the follower cup forward and reassemble the barrel assembly.

Maintenance

Cleaning: always keep the follower cup free of impurities. Your grease should be clear

of any foreign particles, dirt etc and the gun should be checked and cleaned regularly.

Air pockets in grease:

If the gun is pumped but no grease appears from the coupler: Depress the air bleeder valve on the head and pump a few strokes.

Unscrew the barrel assembly from the gun head with two or three turns and then push on the plunger rod. With the follower cup

engaged, the follower cup will move further down into the barrel venting any trapped air out through the thread connections

between the barrel and head. Unscrew the flex extension as well.

Safety Warning

Always use safety goggles and gloves when operating this grease gun. Personal injury may occur and if so seek immediate

medical attention. Do not use a high pressure grease fitting as a loader fitting. Excessive pressure can cause personal injury

and equipment damage.

NSW/ACT

QLD/PNG

TEL: (02) 9677 1555

TEL: (07) 3204 9166

FAX: (02) 9675 1155

FAX: (07) 3204 1224

OWNER'S MANUAL

Trigger Action Grease Gun

400gm Grease Cartridges, Suction loading, Bulk loader pump from bulk grease drum

Maximum operating pressure of up to 8,500psi

0.70g per stroke (high pressure setting) / 1.1cc per stroke (high volume setting)

500g capacity when using bulk grease

VIC/TAS

TEL: (03) 8787 8288

FAX: (03) 8787 8266

Visit our website at

www.alemlube.com.au

SA/NT

TEL: (08) 9302 4199

TEL: (08) 8241 7111

FAX: (08) 9303 2095

FAX: (08) 8241 7011

www.alemlube.co.nz

220A

December 2021

TEL: (09) 447 1007

FAX: (09) 447 1008