BD Sensors BAROLI 05 Instrukcja obsługi
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Przyrządy pomiarowe BD Sensors BAROLI 05. BD Sensors BAROLI 05 2 stron. Digital pressure gauge
Również dla BD Sensors BAROLI 05: Instrukcja montażu (2 strony)
Drukuj stronęEN
Operating Manual
BAROLI 02, 05, 02 P, 05 P
Digital pressure gauge
www.bdsensors.com
Headquarters
Eastern Europe
BD SENSORS GmbH
BD SENSORS s.r.o.
BD-Sensors-Str. 1
Hradištská 817
D - 95199 Thierstein
CZ - 687 08 Buchlovice
Germany
Czech Republic
Tel.: +49 (0) 9235-9811-0
Tel.: +42 (0) 572-4110 11
Fax: +49 (0) 9235-9811-11
Fax: +42 (0) 572-4114 97
Russia
China
BD SENSORS China Co, Ltd.
BD SENSORS RUS
39a, Varshavskoe shosse
Room B, 2nd Floor, Building 10,
RU - Moscow 117105
No. 1188 Lianhang Rd.
201112 Shanghai,
Russia
China
Tel.: +7 (0) 95-380 1683
Tel.: +86 (0) 21-51600 190
Fax: +7 (0) 95-380 1681
Fax: +86 (0) 21-33600 613
further agencies in:
EUROPE
•
• Romania
Belgium
•
• Sweden
Denmark
•
• Switzerland
Finland
•
• Slovakia
France
•
• Spain
Great Britain
•
• Turkey
Greece
•
• UK
Italy
•
• Ukraine
Lithuania
•
Luxemburg
•
Netherlands
AFRICA
•
Norway
• Egypt
•
Poland
• South Africa
• Portugal
The addresses of our distribution partners are listed on our
homepage www.bdsensors.com. It is possible to download
data sheets, operating manuals, ordering codes and certifi-
cates, as well.
1. General information
1.1 Information on the operating manual
This operating manual contains important information on
proper usage of the device. Read this operating manual
carefully before installing and starting up the pressure
measuring device.
Adhere to the safety notes and operating instructions which
are given in the operating manual. Additionally applicable
regulations
regarding
occupational
prevention as well as national installation standards and
engineering rules must be complied with!
This operating manual is part of the device and must be
kept at a, for the personnel always accessible location,
close to the installation position of the device.
This operating manual is copyrighted. The contents of this
operating manual reflect the version available at the time of
printing. It has been issued to our best knowledge and
belief. However, errors may have occurred. For incorrect
statements and their consequences, liability cannot be
assumed by BD SENSORS.
– Technical modifications reserved –
1.2 Symbols used
DANGER! – Dangerous situation, which may result in
serious or fatal injuries
WARNING! – Potentially dangerous situation, which
may result in fatal or serious injuries
CAUTION! – Potentially dangerous situation, which
may result in minor injuries
!
CAUTION! – Potentially dangerous situation, which
may result in damage of objects
NOTE – Tips and information for the user to ensure
good conditions for the operation.
1.3 Target group
WARNING! To avoid hazards for the operator and
damages of the device, following described instructions
have to be worked out by qualified technical personnel.
1.4 Limitation of liability
No liability is assumed and warranty claims are excluded in
case of non-observance of the operating manual, improper
application, modification of or damage to the device.
1.5 Intended use
- The battery powered digital pressure gauge BAROLI has
been exclusively designed for applications in hydraulics
and pneumatics as well as for mechanical engineering.
It can be easily and quickly installed in situ.
- It is in the responsibility of the user to verify whether the
chosen device is suitable for the intended application.
In case of any doubts, contact our sales department to
eliminate any indistinctness. BD SENSORS does not
assume any liability for an incorrect selection and its
consequences!
- Permissible media are gases or liquids, which are
compatible with the media wetted parts described in
the data sheet. In addition it has to be ensured, that
this medium is compatible with the media wetted parts.
- The technical data listed in the current data sheet are
engaging. If the data sheet is not available, please or-
der or download it from our homepage.
(http://www.bdsensors.com)
WARNING! – Danger through improper usage!
1.6 Package contents
Please verify that all listed parts are undamaged included in
the delivery and check for consistency specified in your
order:
- digital pressure gauge BAROLI
- mounting instructions
2. Product identification
The device can be identified by its manufacturing label. It
provides the most important data. By the ordering code, the
product can be clearly identified. For identification of the
ASIA
firmware the program version will appear for about 1 second
• India
in the display after starting up the device. Please hold it
• Iran
ready for inquiry calls.
• Israel
Type designation
• Japan
Input
• Kazakhstan
• Malaysia
• Singapore
• Taiwan
• Thailand
• Vietnam
AUSTRALIA
Fig. 1 manufacturing label
!
The manufacturing label must not be removed from the
device!
3. Mechanical installation
3.1 Mounting and safety instructions
WARNING! Install the device only when depressurized
and currentless!
WARNING! This device may only be installed by
qualified technical personnel who has read and
understood the operating manual!
!
Handle this electronic precision measuring device
carefully in packed as well as in unpacked condition!
!
The device must not be subject to any changes or
safety,
accident
modifications.
!
The device may not be thrown!
!
To avoid damaging the diaphragm, remove packaging
and protective cap only directly before starting up the
device. A delivered protective cap must be stored!
!
Place the protective cap on the pressure port again
immediately after disassembling.
!
Handle the unprotected diaphragm very carefully - it is
very sensitive and may be easily damaged.
!
Do not use any force when installing the device to
prevent damage of the device and the plant!
!
3.2 General installation steps
- Carefully remove the pressure measuring device from
- Then go ahead as detailed in the specific instructions
3.3 Installation steps for DIN 3852
- Check to ensure the proper groove fitting of the o-ring
- Ensure that the sealing surface of the taking part is
- Screw the device into the corresponding thread by
- If you have a device with a knurled ring, the transmitter
- Devices with a spanner flat have to be fully tightened
- The indicated tightening torques must not be ex-
3.4 Installation steps for EN 837
- Use a suitable seal, corresponding to the medium and
- Ensure that the sealing surface of the taking part is
- Screw the device into the corresponding thread by
- Tighten it with a wrench (for G1/4": approx. 20 Nm; for
- The indicated tightening torques must not be ex-
3.5 Installation steps for NPT
- Use a suitable seal (e. g. a PTFE-strip).
- Screw the device into the corresponding thread by
- Tighten it with a wrench (for 1/4" NPT: approx. 30 Nm;
- The indicated tightening torques must not be ex-
3.6 Installation steps for dairy pipe
- Check to ensure that the O-ring fits properly into the
Ordering code
Serial
- Center the dairy pipe connection in the counterpart.
number
- Screw the cup nut onto the mounting part.
- Then tighten it with a hook wrench.
3.7 Installation steps for Clamp and Varivent
- Use a suitable seal corresponding to the medium and
- Put the seal onto the corresponding mounting part.
- Center the Clamp or Varivent
- Then fit the device with a suitable fastening element (e.
3.8 Installation steps for connecting flanges
- Use a suitable seal corresponding to the medium and
- Put the seal between connecting flange and counter
- Install the device with 4 resp. 8 screws (depending on
3.9 Positioning of the display module
The display module of the pressure gauge is rotatable so
that clear readability is guaranteed even on unusual
installation positions.
4. Supply / changing the batteries
The digital pressure gauge is supplied by two 3.6 V-lithium-
batteries (Type 1/2 AA). Stored values/parameters are also
kept after changing the batteries.
If the symbol for low batteries is indicated in the display, it is
necessary to replace them as soon as possible with two
new ones of the same type in order to ensure a good
readability of the values. This has only to be done in
switched-off condition.
The battery case is located under the black, circular plastic
cap on the top of the housing. To change the batteries go
ahead as follows:
The display and the plastic housing are equipped with
rotational limiters. Please do only rotate the display or
the housing within the limit.
Take note that no inadmissibly high mechanical
stresses occur at the pressure port as a result of the
installation, since this may cause a shifting of the
characteristic curve or the demage.
In hydraulic systems, position the device in such a way
that the pressure port points upward (venting).
Provide a cooling line when using the device in steam
lines.
the package and dispose of the package properly.
below.
DO NOT USE ANY ADDITIONAL SEALING MATERI-
ALS, LIKE YARN, HEMP OR TEFLON TAPE!
and additionally to ensure no damage to the o-ring.
perfectly smooth and clean. (R
3.2)
Z
hand.
has to be screwed in by hand only.
with an open-end Devices with a spanner flat have to
be tightened with an open-end wrench (G1/4": approx.
5 Nm; G1/2": approx. 10 Nm; G3/4": approx. 15 Nm;
G1": approx. 20 Nm; G1 1/2": approx. 25 Nm).
ceeded!
the pressure input (e. g. a cooper gasket).
perfectly smooth and clean. (R
6.3)
Z
hand.
G1/2": approx. 50 Nm).
ceeded!
hand.
for 1/2" NPT: approx. 70 Nm).
ceeded!
intended groove in the mounting part.
the pressure input.
connection on the fitting
counterpart with seal.
g. semi-ring or retractable ring clamp) according to the
supplier's instructions.
pressure input. (e. g. a fiber gasket).
flange.
flange version) on the counter flange.