Alemlube HR40041 Instrukcja techniczna dla właściciela - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja techniczna dla właściciela dla Narzędzia Alemlube HR40041. Alemlube HR40041 5 stron. Spring rewind hose reels

Drukuj stronę

(psi/bar)

27667203-18

300/20

27667203-28

300/20

2766 for air wall & ceiling

27667204-31

140/10

27667204-21

140/10

27667155-31

140/10

27667155-21

140/10

Safety Precautions

General Safety Rules

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

WARNING: The warnings, cautions, and instructions discussed in this instruction manual

cannot cover all possible conditions or situations that could occur. It must be understood by

the operator that common sense and caution are factors which cannot be built into this

product, but must be supplied by the operator.

Hose Reel Safety Precautions

1. Use proper eye protection when assembling and using the hose reel.

2. Keep children away from the work area.

3. Personal injury and/or equipment damage may result if proper safety precautions are not

observed.

4. Ensure that reel is properly installed before connecting input and output hoses.

5. Bleed fluid/gas pressure from system before servicing reel.

6. Before connecting reel to supply line ensure that pressure does not exceed maximum

working pressure rating of reel.

7. Remember, even low pressure is very dangerous and can cause personal injury or death.

8. If a leak occurs in the hose or reel, remove system pressure immediately.

9. Ensure that reel, hose, and equipment being service are properly grounded.

2766 for water wall

10. If reel ceases to unwind or rewind, remove system pressure immediately.

11. o not pull or jerk on hose.

Installation of Hose Reel

You will need to purchase appropriate hardware for mounting your new reel.

1) For mounting: For air series, Install reel on the wall and ceiling at most 9feet / 3m above the

floor. For water series, Install reel on the wall at most 4.5feet / 1.5m above the floor .

2) The reel base has two mounting holes for mounting on a suitable flat surface for air series

(four mounting holes for water series). Below figures is a template showing the correct

location of the mounting holes in the base.

3) Using the mounting holes in the base, mount the reel in the desired location. Be sure to use

appropriate hardware and tighten securely.

4) The end of incoming hose can be connected to desired supply source.

5) Outlet fittings on reel hose attach to desired tool, or nozzle. Check connection for leakage,

also check hose reel for correct operation. See: Operation section.

6) If hose stopper adjustment is required, pull hose from reel and allow to latch at desired

Plastic Spring Driven Reel 2766 Series Instruction

length. Loosen stopper bolts, and slide stopper to a position close to the hose guide. Tighten

stopper bolts, and unlatch the reel.

HR40000 for air and water - wall and ceiling mount

2766 for air wall & ceiling

2766 for water wall

NSW

QLD/PNG

TEL: (02) 9677 1555

TEL: (07) 3204 9166

FAX: (02) 9675 1155

FAX: (07) 3204 1224

Visit our website at

Work Tem.(˚C)

Air

PVC

Air

PVC

Water

PVC

EL 40000 Series Instruction

Water

PVC

Water

PVC

Water

PVC

1 OF 4

2 OF 4

VIC/TAS

TEL: (03) 8787 8288

FAX: (03) 8787 8266

www.alemlube.com.au

(inch/mm)

-20～60

3/8" /10

-20～60

3/8" /10

0～60

1/2" /12

0～60

1/2" /12

0～60

5/8" /15

0～60

5/8" /15

TEL: (08) 9302 4199

FAX: (08) 9303 2095

www.alemlube.co.nz

(m/ft)

20/65

Operation

20/65

1. Check reel for correct opera

2. To latch the reel, pull out th

20/65

stops retracting.

15/50

3. To unlatch the reel, slowly p

15/50

until the hose stopper rests

Note: To avoid damage to t

4. Periodically check the hose

for leakage. Replace any wo

Maintenance

Make sure the hose is in prop

Clean the hose with a cloth di

correct rewinding.

Do not use detergents or solv

Dismantling of the unit by uns

concern the preloaded spring

Limited Warranty

1. The manufacturer warrante

for a period of 24 months fr

2. Manufacturer's liability is lim

warranty period, when retur

service depot.

3. The warranty does not cove

4. The reel must be installed a

Operation

1. Check reel for correct opera

2. To latch the reel, pull out th

stops retracting.

3. To unlatch the reel, slowly p

until the hose stopper rests

Note: To avoid damage to t

4. Periodically check the hose

for leakage. Replace any wo

Maintenance

Make sure the hose is in prop

Clean the hose with a cloth di

correct rewinding.

Do not use detergents or solv

Dismantling of the unit by uns

concern the preloaded springs

Limited Warranty

1. The manufacturer warrantee

for a period of 24 months fr

2. Manufacturer's liability is lim

warranty period, when retur

service depot.

3. The warranty does not cove

4. The reel must be installed a

SA/NT

TEL: (08) 8241 7111

TEL: (64) 9 447 1007

FAX: (08) 8241 7011

FAX: (64) 9 447 1008

Plastic Spring