Bosch HBC86K7 3S Series Instrukcja obsługi - Strona 14
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Piekarnik Bosch HBC86K7 3S Series. Bosch HBC86K7 3S Series 40 stron. Compact oven with microwave
Drukuj stronę
Set a later end time by turning the rotary selector.
2.
7LPHVHWWLQJ RSWQ
(QG
7LPHU
([LW ZLWK
0
Press the
button to close the time-setting options menu.
3.
Confirm by pressing the
4.
The setting is adopted. The oven is in
time is displayed in the status bar. When operation starts, the
cooking time starts counting down in the status bar.
The cooking time has elapsed
A signal sounds. The oven stops heating. The status bar shows
0
the cooking time as 00:00:00. You can cancel the signal early
by pressing the
button.
Correcting the end time
This is possible while the oven is in standby. Press the
button to open the menu. Press the
End time using the rotary selector. Press the
the menu.
Cancelling the end time
This is possible while the oven is in standby. Press the
button to open the menu. Press the
End time using the rotary selector. Press the
the menu.
Setting the timer
The timer runs independently of the oven. You can use it as a
kitchen timer and set it at any time.
0
1.
Press the
button.
The time-setting options menu appears.
2.
Set the running time for the timer using the rotary selector.
0
Press the
button to close the Time-setting options menu.
3.
The display returns to its previous state. The
timer appears, and the time can be seen counting down.
Memory
Memory gives you the option to store your own settings and
call them up again at the press of a button. There are six
memory locations available. The memory function is useful for
recipes which you prepare particularly frequently.
Storing settings in the memory
Set the required operating mode. Do not start.
1.
f
Press and release the
2.
select one of the six memory locations.
f
3.
Press and hold the
button until "Memory saved" is
displayed.
The setting is saved and can be started at any time.
Reallocating a memory location
f
Make the settings, select the memory location and save the
new settings using the
overwritten.
Starting the memory
You can start the saved settings at any time.
14
n
button.
0
... standby. The end
X
0
button and correct the
button to close
X
0
button and reset the
button to close
U
symbol for the
button and use the rotary selector to
button. The old settings are
When the time has elapsed
U
A signal sounds. The time has elapsed. The display shows
00:00. You can cancel the signal earlier by pressing the
button.
Cancelling the timer time
0
Press the
button to open the time-setting options menu.
0
Using the rotary selector, turn the time back to 00:00. Press
the
button to close the menu.
Changing the timer time
0
Press the
button to open the time-setting options menu. Use
the rotary selector within the next few seconds to change the
time on the timer. Press the
Setting the clock
The oven must be switched off before you can set or change
the clock.
Following a power cut
Following a power cut, the "Basic settings" heading appears in
the display.
0
1.
Set the right time using the rotary selector.
0
Press the
2.
The time is applied.
Changing the clock
0
Example: changing from summer to winter time.
0
Press the
1.
The time-setting options menu appears.
X
Use the
2.
Change the time using the rotary selector.
3.
0
4.
Press the
The Time-setting options menu closes. The time is changed.
Hiding the clock
The current time appears in the display when the oven is
switched off. You can hide the clock. For more information,
refer to the Basic settings section.
1.
Press and release the
select the memory location.
The stored settings are displayed. If "Memory location empty"
appears, this means that there are no settings stored as yet
in this memory location.
n
2.
Press the
The memory function starts.
Changing the memory location
Once operation has started, you can no longer change the
memory location.
Changing the settings
This can be done at any time. The setting you originally saved
appears the next time you start the memory.
0
button to close the menu.
button.
button.
button to switch to the clock.
button.
f
button and use the rotary selector to
button.
0