Electrolux EIFLW55HIW - 27" Front-Load Washer Arkusz danych technicznych

Przeglądaj online lub pobierz pdf Arkusz danych technicznych dla Spryskiwacz Electrolux EIFLW55HIW - 27" Front-Load Washer. Electrolux EIFLW55HIW - 27" Front-Load Washer 16 stron. Iq-touch front-load washer
Również dla Electrolux EIFLW55HIW - 27" Front-Load Washer: Specyfikacje (2 strony), Specyfikacje (2 strony), Instrukcja obsługi i konserwacji (32 strony), Specyfikacja (2 strony), (Hiszpański) Instrukcja obsługi i konserwacji (36 strony), (francuski) Guide D'utilisation Et D'entretien (36 strony)

Electrolux EIFLW55HIW - 27
CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING
Please Return This Sheet to its Envelope in the Product for Future Reference
Acronyms:
MB – Main Board (Board located inside machine on right side just behind control panel.)
MC – Motor Control
UI – User interface board (board located inside the front control panel)
DL – Door Lock
READING ERROR CODES
1. Wake the washer up by pressing any button (except the cancel button).
2. Press and hold the "Cancel" and "Start" buttons simultaneously for 6 seconds. The failure code will appear in the
display as an E followed by two numbers.
NOTE: E00 means no failure code experienced. Troubleshoot the problem by using charts on the pages 3-5.
If there is no error displayed and the washer momentarily starts then turns back off:
1. Listen for a relay closure inside the control shortly after the "Start/Pause" key is pressed.
2. Check the connections on the MB make sure that they are firmly snug and secured.
To clear latest stored error code:
Press the "Cancel" button to enter standby mode and enable diagnostic entry.
Within 10 seconds after pressing "Cancel", press any button to wake up the control.
Within 5 seconds of wake up, turn the selector knob to the far left cycle and press and hold the "Cancel" and the far left
button under the display simultaneously for 3 seconds to enter the Diagnostic Mode. (note: to save time at wake up,
the welcome screen can be bypassed by turning the selector knob).
Turn the program knob counter clockwise 9 turns (clicks) from the Start Position. The control will signal the last 5 error
codes with E00 meaning no error experienced.
Press and hold the far left key under the display and "Cancel" buttons simultaneously for 3 seconds. The code(s) will
be cleared.
To return the washer to normal operation.
a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord OR
b) Turn the program knob clockwise 2 turns (clicks) back to the Start Position (LEDs are flashing).
Press the "Cancel" and far left button under the display until the LEDs stop flashing.
Diagnostic Test
The diagnostic test is used to check individual component function only.

TO START THE TEST:

Press the "Cancel" button to enter standby mode and enable diagnostic entry.
Within 10 seconds after pressing "Cancel", press any button to wake up the control.
Within 5 seconds of wake up, turn the selector knob to the far left cycle and press and hold the "Cancel" and the far left
button under the display simultaneously for 3 seconds to enter the Diagnostic Mode. (note: to save time at wake up,
the welcome screen can be bypassed by turning the selector knob).
1. Upon entering Diagnostic Mode, all lights should flash for 1¼"x2" display models and all lights on for the 1¼"x4¾" display
models.
Washer Tech Data Sheet
This information is intended for Qualified Technicians Only.
Contents
Error code explanation.............................................1
Diagnostics ........................................................1-2
Error Code Chart.....................................................3
Tests..................................................................4-5
Français.........................................................6-10
Español........................................................11-15
Wiring Diagram..................................................16
Page
1
137022700A (0805)