Alemlube 5060A Instrukcja techniczna dla właściciela
Przeglądaj online lub pobierz pdf Instrukcja techniczna dla właściciela dla Pompa wodna Alemlube 5060A. Alemlube 5060A 2 stron. High volume refuelling drum pumps
Drukuj stronęDescription
Model 5040/5060A is a high volume, manually operated, rotary action drum pump that delivers up to 100 L/min. It is designed for
the refuelling of both on and off road vehicles and large machinery. The simple design of the 5040/5060A allows easy servicing
if required. The pump comes complete with delivery hose and includes a replaceable foot filter. * PLEASE NOTE: OIL GEARS
BEFORE USE (SAE 30 oil is recommended for this purpose).
Specifications
Uses
Discharge Quantity
Materials
Weight
Size
Operating instructions
1 Oil Gears Before Use
Before using the 5040/5060A high volume rotary refuelling pump,
make sure that you fill the gear cover with oil. Fill with SAE 30 oil
or equivalent to the reference line through the lubrication bolt hole
(as indicated on the diagram). Inspect periodically.
2 Revolution Direction
The handle turns in a clockwise direction and the pump discharges
one litre per one revolution of the handle.
3 Filter
A filter of #60 mesh polyethylene net is supplied as standard on the
pump and is located at the bottom of the suction pipe. Rotating the
handle and therefore operating the pump may become harder if
the filter is clogged with impurities that may have been filtered
out of the fuel or low viscosity oil. It is recommended that you
remove the filter periodically and clean it with kerosene.
4 Cautions
Suitable liquids include most low viscosity liquids such as diesel,
unleaded petrol, kerosene and low viscosity oils. Although the pump
can be used to pump other liquids of high viscosity, the pump becomes
harder to operate and doing so will shorten the life of the pump & may
void the warranty.
Do not use this pump for any solvent or chemical transfer as these liquids will
dissolve the Buna N seals and gaskets, etc. (Use the 301-A, 401-A, 733 or 933
for solvents).
Please note when pumping fuels like kerosene, petrol or diesel, these products
tend to "dry out" the internals of the pump causing parts "to stick" and the pump not
to prime and dispense. To stop this from happening and to increase the working life
of your pump, we recommend that you lubricate the gears of the pump by dropping
a few drops of oil into the pump body by taking off suction pipe (2000-42) &
lubricating at this opening. After undertaking lubrication of the pump in such a
manner, please rotate the handle a few times.
Do not pump liquids containing dirt or particles such as waste oil. Strained liquids
may block the filter, preventing discharge, which can damage the pump interior or
cause other problems.
NSW/ACT
QLD/PNG
TEL: (02) 9939 0711
TEL: (07) 3204 9166
FAX: (02) 9939 0411
FAX: (07) 3204 1224
Visit our website at
OWNER'S TECHNICAL MANUAL
High Volume Refuelling Drum Pumps
Diesel and low viscosity oils up to SAE 30
1L per rotation / 100 L/min
Cast Aluminium, Buna N Seals
7.0kg
Suction pipe: 32mm ID x 1m
Delivery hose: 5040 - 25mm ID x 1.2mm long, 5060A - 25mm ID x 2.2mm long
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
www.alemlube.com.au
5060A
WA
SA/NT
TEL: (08) 9302 4199
TEL: (08) 8241 7111
FAX: (08) 9303 2095
FAX: (08) 8241 7011
Email - [email protected]
5040
5060A
5040
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008