Bosch HVA531NS0/04 Instrukcja obsługi - Strona 11
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Piekarnik Bosch HVA531NS0/04. Bosch HVA531NS0/04 16 stron.
Drukuj stronę
Removing and inserting the hook-in racks
You can remove the hook-in racks for easier cleaning.
Removing the hook-in racks
The hook-in racks are each fixed to the side panels of the
cooking compartment at three points.
Grip the front of the hook-in rack and pull it to the middle of
1.
the cooking compartment.
The front hook of the hook-in rack will release from the hole.
Fold out the hook-in rack further and pull it from the rear
2.
holes of the side panel.
Hold the catalytic cooking compartment panel in place.
3.
Troubleshooting
Malfunctions often have simple explanations. Please read the
following notes before calling the aftersales service.
Problem
Possible cause Notes/remedy
The appliance
Circuit breaker
does not work.
faulty.
Power cut
The oven can-
The electronics
not be switched
are faulty.
off.
A beep sounds
The tempera-
every second.
ture probe is
faulty.
A beep sounds
The tempera-
twice per sec-
ture in the oven
ond.
interior is too
high.
The clock dis-
Power cut
play flashes.
The oven does
Circuit breaker
not heat up.
faulty.
The function
selector has not
been set.
The door glass
is broken.
Fruit juice or
Moist cake or
albumen stains
meat juices.
on enamelled
surfaces.
:
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out by one of our trained after-sales engineers.
Incorrect repairs may result in significant risk to the user.
Look in the fuse box and
check that the circuit
breaker for the cooker is in
working order.
Check whether the kitchen
light works.
Switch off the circuit
breaker. Contact the after-
sales service.
Turn the function selector to
the Off position.
If the beeping persists when
setting a new heating func-
tion, switch off the appli-
ance and contact the after-
sales service.
Reset the clock.
Check the circuit breaker
and replace if necessary.
Set the function selector.
Switch off the appliance.
Contact the after-sales ser-
vice.
Harmless change in the
enamel, cannot be
removed.
Remove the hook-in rack from the cooking compartment.
4.
Inserting the hook-in rack
Hold the catalytic cooking compartment panel in place.
1.
Insert the hooks of the hook-in rack into the rear holes in the
2.
side panel.
Press the front hook of the hook-in rack into the hole.
3.
Replacing the oven light bulb
If the oven light bulb fails, it must be replaced. Replacement
heat-resistant bulbs can be obtained from the after-sales
service or from specialist retailers. Please specify the E number
and FD number of your appliance. Do not use any other type of
bulb.
:
Risk of electric shock!
When replacing the cooking compartment bulb, the bulb socket
contacts are live. Before replacing the bulb, unplug the
appliance from the mains or switch off the circuit breaker in the
fuse box.
Allow the cooking compartment to cool down.
1.
Open the appliance door.
2.
Place a tea towel in the cooking compartment to prevent
3.
damage.
Remove the hook-in racks.
4.
Remove the glass cover. To do this, open the glass cover at
5.
the front with your hand. Should you experience difficulties
removing the glass cover, use a spoon to help.
Remove the oven light bulb.
6.
Replace the oven light bulb with a bulb of the same type:
7.
Voltage: 230 V;
Power: 40 W;
Fitting: G9;
Temperature resistance: 300 °C
Refit the glass cover for the oven light bulb.
8.
Refit the hook-in racks.
9.
Remove the tea towel.
10.
Switch the circuit breaker back on.
11.
Check that the oven lighting is working again.
12.
11