Bosch 1614 Instrukcja obsługi - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Elektronarzędzie Bosch 1614. Bosch 1614 28 stron. Plunge router
Również dla Bosch 1614: Instrukcja obsługi (28 strony)

Drukuj stronę

• DONOTALTER ORMISUSE T OOL.

These tools a re precision

built. A ny alterations

ormodifications

notspecified ismisuse and

may result inadangerous

condition.

• THEUSE OFANYACCESSORIES

not

specified

inthis manual may create ahazard.

• MAINTAIN T OOLS W ITH CARE. Keep

tools sharp and c lean forbetter and s afer perfor-

mance. Follow i nstructions

forlubricating

and

changing

accessories.

Inspect tool c ords peri-

odically and if damaged,

have r epaired byau-

thorized service facility.Inspect extension

cords periodically

and r eplace ifdamaged.

Keep

handles

dry, clean a nd f ree from oiland grease.

• CHECK D AMAGED PARTS. Before fur-

ther u se ofthe tool, aguard orother part that is

damaged

should be carefully checked

todeter-

mine t hat i twilloperate properly and perform

itsintended

function. Check foralignment

moving parts, binding ofmoving parts, break-

age ofparts, mounting,

and any other condi-

tions t hat m ay affect itsoperation. Aguard o r

other part t hat isdamaged

should bepromptly

and p roperly repaired

orreplaced.

Have d efec-

tive switches

replaced.

Do not u se t ool ifswitch

does n ot t urn itonoroff.

• ALLREPAIRS,

ELECTRICAL

ORME-

CHANICAL, should b eattempted

onlyby

trained repairmen.

Contact the nearest Bosch

Factory Service Center, orBosch Authorized

Service Center orother competent

repair cen-

ter. Use only Bosch r eplacement

parts, any

other may create ahazard.

• If router bitisprotruding

through the base,

never laythe router down u nti! t he motor has

come t oacomplete

standstill.

• Never hold the workpiece

inone hand a nd

the router inother when i nuse. Always clamp

the material and hold the router securely

with

both hands.

• Never use bits that have a cutting d iameter

greater than t he opening inthe base.

• After changing

the bits ormaking any adjust-

ments, make s ure t he collet nutand any other

adjustment

devices are securely tightened

be-

fore using t he router.

• The direction offeeding the router into the

material isvery important

and itrelates tothe

direction ofbitrotation. When v iewing t he

router from the top, t he bitrotates clockwise.

When the router islocated between your b ody

and the material, the feed direction must be to

the right, lfthe material

islocated between

your

body and therouter, then thefeed direction

must betothe left.Feeding the router inthe

wrong d irection causes the cutting edge o fthe

bittoclimb out o fthe work and pull t he router

inthe direction of this feed.

• Double Insulation [] is a design concept

used i nelectric power tools which e liminates

the need forthe three w ire grounded

power cord

and grounded

power supply s ystem. It is a

recognized a nd approved systemby

Underwriter's

Laboratories,

CSA and Federal

OSHA a uthorities.

• Never start the router when t he bitisengaged

inthe material. The b it's cutting edge may g rab

the material causing the router togetoutof

control. Always hold t he router with two hands

during s tart-up. The reaction torque o fthe

motor can cause the router totwist.

• Always make sure t he workpiece

isfree from

nails a nd other foreign objects which c an cause

the bitand router tojump and damage

the bit.

• Always wear safety goggles. If router has a

removable

chip deflector,

keep itinplace w hen

routing.

• Never touch t he router bitorother moving

part during u se. A fter u se the router bitistoo

hot t obetouched

bybare h ands.

IMPORTANT: S ervicing of a toolwith

double insulation

requires care a nd k nowledge

ofthe system a nd should beperformed

only by

aqualified service technician. WHEN SER-

VICE ISREQUIRED

USE ONLY IDENTI-

CALREPLACEMENT

PARTS.

POLARIZED

PLUGS: Ifyour tool i sequipped

withapolarized

plug (one b lade i swider than

the other), this plug will f itinapolarized

outlet

only one w ay. Ifthe plug does not f itfullyinthe

outlet, reverse the plug.If it stilldoes n ot f it,

contact a qualified electrician to install the

proper outlet. Toreduce theriskof electric

shock donot c hange the plug inany way.