Anchor ETI 30’CLASSIC FRAME TENTS Instrukcja montażu - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja montażu dla Namiot Anchor ETI 30’CLASSIC FRAME TENTS. Anchor ETI 30’CLASSIC FRAME TENTS 8 stron.

Drukuj stronę

SAFETY BEST PRACTICES

Economy Tent International products are of superior design

and function best in the parameters of these instructions. It

is recommended that the instructions are carefully read and

followed. Please read these "Safety Best Practices" before

the installation or removal of any tent.

• The installer is solely responsible for the evaluation of the

site and determining the proper securing method. Some

soils require different staking or securing other than what is

provided with the tent or purchased by the customer. Our

responsibility is limited to the construction of the tent and

not damage due to installation. Damaged frame parts or

fittings are usually caused by improper lifting of the frame

and are not covered under the terms of the warranty.

• Installation during threatening weather conditions is not

advised under any circumstances. It is the responsibility

of the tent installer/maintainer to determine the severity of

the weather and utmost care must be used. This product

is to be used as a temporary structure. In any questionable

weather conditions, evacuation is recommended and all

valuable merchandise should be removed immediately.

Use good judgment, common sense and safety during

take-down of the tent.

• Due to shifting of the tent frame, loosening of the stakes or

loosening buckles, it is possible for the cover to "pocket"

water in rain conditions. It is imperative to continually

inspect the frame and cover for proper fit and alignment

and adjust as required.

• Proper safety equipment should be used at all times to

insure a safe installation and take down. Careful evaluation

should be made to determine if hard hats, steel toe shoes,

safety glasses and any other equipment should be used

for the safe and proper installation. Tent lifts or other

equipment might be considered for lifting or take down.

GENERAL CARE & MAINTENANCE

SOLID COVER & SIDEWALL VINYL

The vinyl fabric developed for this tent system requires specific

attention during installation, cleaning, and storage to maintain

its maximum life span. Please follow the following care and

maintenance guidelines provided for this product.

MILDEW TREATMENT: Our vinyl fabric is pretreated with

mildew inhibitors that help prevent the growth and spreading of

mildew and fungus. If you see mildew wipe it away immediately

with a clean towel and diluted soap solution. Never fold tent

covers if the fabric is even slightly wet since mildew will grow

in moist environments.

CLEANING: The best way to clean the vinyl tent fabric is

with a soft towel or soft bristled brush immersed in a diluted

solution of warm water and a tent cleaning solution. Apply the

diluted solution directly to the fabric using 1) a towel immersed

in the solution, or 2) a spray bottle or larger pressurized

spraying apparatus to evenly cover the fabric with the solution.

Let this sit on the fabric for about one minute to allow the

mixture to penetrate the fabric. Using a soft towel or soft

bristled polypropylene brush, gently work the cleaner into the

fabric using only mild pressure. Never allow the tent cleaner to

STAKING / ANCHORING BASICS

By law you are required to contact your local "Call before you

dig" number before you plan to dig or drive tent stakes for your

local utility company to mark the location of all underground

utility lines. Laws vary from state to state as to how far in

advance you must call. Plan in advance.

Soil and setup conditions can vary greatly between installation

sites. It is the installer's responsibility to be sure the staking is

adequate for each site on each setup.

5" to 6"

STAKING BASICS

A properly driven

stake will have 6"

or less of the head

exposed. The

deeper the stake,

the greater the

CORRECT ANGLE

holding strength.

Anchoring stakes

must be driven

deep and vertical

(not at an angle)

about 5' to 6'

away from the

tent.

5' to 6'

dry on the fabric. Once the cleaning is complete be sure to rinse

away any cleaning solution completely. The best way to dry the

vinyl tent fabric is to hang-dry in a low humidity environment.

Fans can be used to circulate air but do not use heated dryers.

STORAGE: Store in a cool, dry area in the storage bags that

came with your cover.

FRAME HARDWARE & COMPONENTS

The hardware components developed for this tent system

require specific attention during installation, cleaning, and

storage to maintain their maximum life span. Please follow the

following care and maintenance guidelines provided for this

product.

OXIDATION: The hardware components for this tent system

have been supplied to you with specialty coatings to help limit

oxidation. With usage, these coatings will need to be maintained

for the product to reach its full intended lifespan.

CLEANING: It is very important to keep your frame

hardware components clean and free of dirt. If soiled, wipe

down immediately to remove the foreign matter.

STORAGE: The tent frame system should be stored dry in a

cool, dry, low humidity covered place.

See full "Care & Maintenance" on economytent.com.

INCORRECT ANGLE