Bosch 30-380 Oryginalna instrukcja obsługi - Strona 16
Przeglądaj online lub pobierz pdf Oryginalna instrukcja obsługi dla Elektronarzędzie Bosch 30-380. Bosch 30-380 22 stron. Angle exact
Drukuj stronę
OBJ_BUCH-412-001.book Page 35 Thursday, April 3, 2008 3:18 PM
Changing Application Tools on the
Screw Head with External Square Drive
When working with an application tool, pay
attention that the application tool is firmly
seated on the tool holder. When the applica-
tion tool is not firmly connected with the tool
holder, it can come loose again and not be
controlled.
ANGLE EXACT 2 | 3 | 6 | 7 | 7 – 900 | 8 |
10 – 650 | 14 – 420 | 15
An angled screw head with 1/4" square drive
(Article number 0 607 453 617) as well as one
with 3/8" square drive (Article number
0 607 453 620) are available for these industrial
cordless angle wrenches.
ANGLE EXACT 7 – 900 | 10 – 650 | 14 – 420 | 17 |
23 | 30
An angled screw head with 3/8" square drive
(Article number 0 607 451 618) is available for
these industrial cordless angle wrenches.
ANGLE EXACT 25 – 250 | 30 – 380 | 40 – 280 |
50 – 210
These industrial cordless angle wrenches are
supplied with a 3/8" sqaure drive angled screw
head.
Inserting
Press in the pin on the drive square of the tool
holder 2, e.g. using a small screwdriver, and
slide the tool bit 1 over the drive square. Pay at-
tention that the pin engages in the recess of the
tool bit.
Removing
Press in the pin in the recess of the tool bit 1
and pull the tool bit out of the tool holder 2.
Bosch Power Tools
Changing Application Tools on the
Screw Head with Internal Hexagon
(see figure F)
When working with an application tool, pay
attention that the application tool is firmly
seated on the tool holder. When the applica-
tion tool is not firmly connected with the tool
holder, it can come loose again and not be
controlled.
ANGLE EXACT 2 | 3 | 6 | 7 | 7 – 900 | 8 |
10 – 650 | 14 – 420 | 15
An angled screw head with 1/4" internal hexa-
gon (Article number 0 607 453 618) is available
for these industrial cordless angle wrenches.
Inserting
Insert the tool bit 1 into the internal hex socket
of the tool holder 2 until it can be felt to engage.
Removing
Pull the tool bit 1 off of the tool holder 2 with
the aid of pliers, if necessary.
Operation
Use safety equipment. Always wear
eye protection. Safety equipment
such as dusk mask, non-skid safety
shoes, hard hat, or hearing protec-
tion used for appropriate conditions
will reduce personal injuries.
Starting Operation
When starting the power tool, you should first
select the direction of rotation with the rotation-
al direction switch 14 since the power tool
starts only when the rotational direction switch
14 is not in the middle position (switch-on lock).
Reversing the Rotational Direction
(see figure G)
Right rotation: For driving in screws, push the
rotational direction switch 14 left to the stop.
Left Rotation: For loosening or unscrewing
screws, push the rotational direction switch 14
right to the stop.
Actuate the rotational direction switch 14
only when the machine is at a standstill.
English | 35
3 609 929 B34 | (3.4.08)