Dream Line AQUA LUX Instrukcja instalacji - Strona 4
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Produkt hydrauliczny Dream Line AQUA LUX. Dream Line AQUA LUX 7 stron. Shower / tub door
Drukuj stronęInstallation
1. Take out Stationary glass panel (01) from the package and find the Wall Brackets (06).
Attach Wall Brackets to the glass panel. Note that the parts of the Wall Brackets with the
mounting holes should face inward so that when glass panels are in place, mounting bolts
are only visible from the inside. See fig. 1 for details.
2. Place the Stationary glass panel with attached Wall Brackets to the designated position
on the threshold or tray, make sure it's leveled and plumbed and mark the position of the
Wall Brackets on the wall. See Fig. 2 for details.
Be sure that the Stationary glass panel is absolutely vertical.
3. Take the glass panel from the threshold and remove the Wall Brackets.
4. Using the removed Brackets, mark the position of the holes for Wall Bracket installation on
the wall. Drill the holes and insert the Wall Anchors (07) into the holes. Attach the Wall
Brackets to wall using the Round head screw ST 4.2×30 (08). See Fig. 3 for details. (Note
that all parts of the wall brackets with the mounting holes should face inward in final
installation).
5. Place the Stationary glass panel against the installed Brackets and secure it to the wall by
attaching the fastening parts of the Wall Brackets to the mounted parts with the supplied
screws.
Note that the hole in the 72" stationary glass for tray and threshold installation should
be at bottom.
6. Locate the Support bar (02) from the package and loosen the glass holding screw on the
gliding channel. Place the Support bar with the channel end on the glass top edge and the
bracket end flat on the wall. Adjust the bar to a proper position and level it horizontally. Hold it
firmly and outline the bracket's position on the wall with a pencil. Take off the Support bar
and remove the bracket from it. Place the bracket against its position on the wall and mark
the position for the drill hole. Drill the hole, insert the anchor and attach the bracket onto the
wall with Screw ST 4.2×30 (08). Replace the Support bar with channel seated on the glass
and the other end underneath the bracket. Attach it to the bracket with the set-screw
provided. Straighten the bar and fasten both set-screws and the glass holding screw to
secure the glass. See fig. 4, 5 for details.
7. Install the Hinges (03) onto the stationary glass with the decorative non-screw side facing
outwards. Hook the Glass door (04) from inside. See fig. 6 for details.
8. Mount the Handle (05) onto the door. Measure the distance between the top edge of the
glass door and upper edge of the top hinge. Cut the piece off the Side strip (09) with a knife
in the length according to your measurement. Repeat it to prepare the short strip for the
lower section of the glass door. Then measure the distance between the bottom edge of the
top hinge and the upper edge of the bottom hinge and cut the rest of the strip to size. Open
the door to its full section and push all the strip lengths onto the vertical edge of the glass
door. Push the Bottom anti-water strip (10) on the bottom edge of the glass door. See fig. 7
for details.
9. Attach the Bottom bracket (13) on the stationary glass and mark a hole in the threshold or
tray through the slotted hole of the Bracket. Remove the Bracket, insert Anchor (07). Then
reinstall the Bracket and screw it onto the threshold or tray with the Round head screw
ST4.2×25 (11) and cover it with the Decorative cover (12). See fig. 8 for details.
NOTE: The Bottom bracket (13) is only applicable for 72" shower door installation (to
the threshold or the shower tray). If your unit is being installed to the bathtub, then
you do not need this bracket.
10. Seal with caulk (recommended 100% clear silicone) inside and outside along the bottom of
the stationary glass and between the wall and the wall bracket. See fig. 9 for details.
Rev.1.2
Page 4