Andersen Windows & Doors 901724 Instrukcja instalacji - Strona 5
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Sprzęt do zwalczania owadów Andersen Windows & Doors 901724. Andersen Windows & Doors 901724 14 stron. 1-1/2” self-storing storm doors with balanced retractable insect screen and integrated close system
Drukuj stronę1" Machine Pan Painted
INSTALL
1-1/2" Machine Flathead
HANDLE SET
4
(Left Hand)
#10
1-1/2" Machine Flathead
a
2" SMS Pan Painted
#12
2
5/8" SMS Pan Painted
3
1.
Make sure the factory applied nylon washer
is in place at the base of both handles.
2.
With trim plates not installed, insert handle
with spindle into outside exterior trim plate
(with Andersen logo) with lever pointing
down and rotate handle to secure it into the
trim plate.
3.
Repeat for other handle without spindle
with inside interior trim plate (with slider).
X
d
VIEW
H
1.
Using pliers, grasp handle
clip (H) and pull away from
latch rail to remove.
2.
Fill holes in latch rail with
color matched plugs
included in installation kit.
1" SMS Pan Painted
1" Machine Pan Painted
I
H
1-1/2" Machine Flathead
Handle Clip
Spacer Clips
#10
b
1-1/2" Machine Flathead
INTERIOR
TRIM PLATE
2" SMS Pan Painted
#12
LOCK
5/8" SMS Pan Painted
CASE
1.
With handle levers held horizontal, install
both handle assemblies onto door. Spindle
will pass through square hole in lock case
and into other handle. Attach interior and
exterior trim plates together using two
1 1/2" pan head screws. Partially install
screws to allow movement for alignment
in following steps.
e
I
J
1.
Remove spacer clips (I) by loosening but not removing screws.
2.
Re-tighten screws. TIP: Use a screw driver to loosen and tighten
screws; a drill driver may strip the screw holes.
3.
Remove bottom spacer (J) by pressing down on raised lip.
4.
Properly discard all orange clips.
1" SMS Pan Painted
J
1-1/2"
1" Machine Pan Painted
Color
1-1/2" Machine Flathead
Bottom Spacer
Matched Plugs
#10
EXTERIOR
TRIM PLATE
1-1/2" Machine Flathead
2" SMS Pan Painted
#12
5/8" SMS Pan Painted
i
VIEW
5
1-1/2"
5/8"
c
INTERIOR
TRIM PLATE
DEAD BOLT
KEY CYLINDER
1.
Install lock case trim plate onto lock case and
partially install 5/8" screw to allow movement.
2.
Insert dead bolt key cylinder into lock case
and partially install 1 1/2" flathead screw to
allow movement. Test deadbolt lock for proper
alignment.
3.
Using a hand held screwdriver, tighten lock
case trim plate screws.
4.
Tighten interior trim plate pan head screws.
5.
Test handle operation. If handle does not
return to horizontal position, then lightly
loosen interior trim plate pan head screws.
NOTE: This door features an integrated latch
receiver in the latch rail, eliminating the need for a
traditional, separate strike plate.
Your storm door lock can be changed (re-keyed) to match your main door' s
handle set if it' s a Kwikset® (included) or a Schalge® (additional purchase
required). Many home improvement stores or locksmiths can make
duplicate keys.
"Kwikset" is a registered trademark of Newfry LLC. "Schlage" is a registered trademark of Schlage
Lock Company.
x 2
1
LOCK CASE
TRIM PLATE
2