Bosch Household Appliances WTC82100US Instrukcja obsługi i instalacji - Strona 8
Przeglądaj online lub pobierz pdf Instrukcja obsługi i instalacji dla Suszarka Bosch Household Appliances WTC82100US. Bosch Household Appliances WTC82100US 24 stron. Condensation dryer
Również dla Bosch Household Appliances WTC82100US: Instrukcja obsługi, konserwacji i instalacji (24 strony), Instrukcja obsługi, konserwacji i instalacji (24 strony), Instrukcja obsługi, konserwacji i instalacji (24 strony), Instrukcja obsługi, konserwacji i instalacji (24 strony)
Drukuj stronę
Electrical
connection
Power cord must be connected
by a licensed electrician
or a
qualified
technician.
Connect
to individual
Branch
Circuit.
Do not use an adapter.
Do not use an extension
cord.
Do not remove ground prong.
For CANADA
Your dryer comes with a power
supply cord, CSA listed in Canada.
The Bosch dryer requires a 4-wire
receptacle.
When installing the receptacle
for
the dryer cord, ensure that the
power supply cord is accessible
when the dryer is in the installed
position.
The power cord should only be
replaced by a qualified person.
Use a 4-wire power supply cord
(see electrical
connection
U.S.A.
below).
For U.S.A.
Your dryer comes with a power
supply cord. Only a 3- or 4-wire
power supply cord shall be used.
The power cord must meet
the following
requirements:
-
ULlisted
in the USA
-
208-240
volt rated (minimum)
-
30 amps
-
Type SRDT or DRT (UL 2158)
-
Five feet long (minimum)
-
marked suitable for dryer
Power cord must be connected
by a licensed electrician
only.
Use only a U.L approved
30 amp power cord with strain
relief clamp - note manufac-
turer's
instructions.
Do not plug end of power cord
into a live receptacle
before con-
necting power cord to appliance
terminals
and closing junction/
splitter box as described
below.
Do not reuse old power cord.
Cord must have closed loop or
upturned
end wire terminating
connectors.
Do not make a sharp bend or
crimp wiring/conductor
at con-
nections.
Only a 4-conductor
cord shall
be used when the appliance
is
installed in a mobile home, in
a recreational
vehicle, in a new
branch circuit installation
or an
area where the local codes do
not permit grounding
through
the neutral.
The splitting box is located at the
top rear of the appliance.
To connect
the power cord you
have to remove the cover plate.
1. Remove the screws of the
cover plate on the rear side
of the appliance.
2. Push the cover plate from the
front to the rear side and lift up.
3. Open the splitting
box in the
right corner (20 Torx).
4. Loosen the strain relief in the
appliance.
5. Thread the power cord through
the U.L strain relief clamp.
6. Tighten the screws (2.5 Nm) of
the U.L strain relief clamp so
that the power cord cannot be
moved.
7. Connect the power cord as
described
below.
8.
After connecting
the power
cord close the splitting box and
replace the cover plate fasten in
place with reverse handling.
Connecting
4-wire
power
supply
cord
1. Remove the screws from the
cover of the terminal block.
2. Remove the screws from the
grounding
cable.
3. Remove the grounding
cable.
4. Loosen the 2 screws labeled L
in the terminal block.
5. Attach the power cord ground
conductor
(green) to the
GROUND
point. Tighten the
screw (2.5 Nm) so that the
ground conductor
is held
securely in place.
6. Attach the 2 power cord outer
conductors
(red and black) to
the 2 terminals
labeled L and
the remaining
power cord
conductor
(white) to the
terminal labeled N.
7. Tighten all 3 screws (3 Nm) so
that the power conductors
are
held securely in place.
8. Check the U.L strain relief
clamp to make sure that it is
tight and cannot be turned.