Bosch Programme Table Instrukcja obsługi - Strona 7

Drukuj stronę

Bosch Programme Table Instrukcja obsługi

Care

Before washing for the first time

Do not load any laundry into the machine. Turn on the tap.

Add the following to compartment II:

– approx. 1 litre water

– detergent (dosage according to the manufacturer's instructions for light soiling and the

appropriate degree of water hardness)

Set the programme selector to

programme, turn the programme selector to Off.

Machine housing, control panel

– Wipe with a soft, damp cloth.

– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).

– Remove detergent and cleaning agent residue immediately.

– Do not clean with a jet of water.

Cleaning the detergent drawer and housing...

... if it contains detergent or fabric softener residues.

1. Pull the drawer out, press down the insert and fully remove the drawer

from the housing.

2. To remove the insert: press the insert upwards from below with your

finger.

3. Clean the detergent dispenser tray and insert with water and a brush and

dry it. Also remove any detergent or fabric softener residues in the

housing.

4. Attach the insert and engage (connect the cylinder to the guide pin).

5. Push in the detergent drawer.

Leave the detergent drawer open so that any residual water can

evaporate.

Washing drum and rubber seal

Wipe the inside of the rubber seal dry with a cloth. Leave the washing machine door open so

that the drum can dry out. Rust stains - use chlorine-free cleaning agent, not steel wool.

Descaling

Ensure there is no laundry in the machine

Descale the appliance according to the descaler manufacturer's instructions. This should not

be necessary if the correct dosage of detergent is used.

Information on the indicator lights

A signal sounds and indicator lights for the spin speed flash:

Close the washing

Detergent solution pump

machine door properly;

blocked; Clean the

laundry may be caught.

detergent solution pump

Drainage hose/waste pipe

blocked; Clean the drainage

hose at the siphon

Motor fault. Call the after-

Water in the base tub,

sales service.

appliance leaking. Call the

after-sales service.

– Risk of electric shock. Disconnect the mains plug.

– Risk of explosion. No solvents.

Easy-Care 60 °C and select Start. At the end of the

model-dependent

Open the tap completely,

supply hose kinked or

trapped;

page 10.

Clean the filter

page 10,

Water pressure too low.

page 10.

Maintenance

Detergent solution pump

Turn the programme selector to Off and disconnect the mains plug.

1. Open and remove the service flap.

2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it

from the housing. Remove the container.

Remove the sealing cap, allow the detergent solution to flow out.

Replace the sealing cap and place the drainage hose in the retainer.

2* For models without a drainage hose: Carefully unscrew the pump cover until the

detergent solution begins to flow out. When the service flap is half full, close the pump cover

and empty the service flap. Repeat the above steps until all the detergent solution has

completely drained out.

3. Carefully unscrew the pump cover (residual water).

4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent

solution pump must rotate).

5. Replace the pump cover and screw it tightly in place.

6. Place the service flap back on and close.

To prevent unused detergent from flowing straight into the drain during the next wash: pour 1 litre of water into

compartment II and start the

Drainage hose at the siphon

Turn the programme selector to Off and disconnect the mains plug.

1. Loosen the hose clamp, carefully remove the drainage hose (residual water).

2. Clean the drainage hose and siphon connecting piece.

3. Reattach the drainage hose and secure the connection with the hose clamp.

Filter in the water supply

Risk of electric shock.

Do not immerse the HydroSafe safety device in water (it contains an electric valve).

Reduce the water pressure in the supply hose:

1. Turn off the tap.

2. Select any programme (except for

3. Select Start. Let the programme run for approximately 40 seconds.

4. Turn the programme selector to Off. Disconnect the mains plug.

Clean the filter:

1. Depending on model:

Disconnect the hose from the tap.

Clean the filter using a small brush.

and/or for Standard and Aqua-Secure models:

Remove the hose on the rear of the appliance.

Remove the filter with pliers and clean.

2. Connect the hose and check for leaks.

– Risk of scalding.

Allow the detergent solution to cool down.

– Turn off the tap.

Drain programme.

Rinse/

Spin //

Drain).