Dreamline Elegance Instrukcja instalacji - Strona 5
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Produkt hydrauliczny Dreamline Elegance. Dreamline Elegance 14 stron. Shower door
Drukuj stronęAssemble Steps
1. Locate the Wall profile for glass door (1) and place it vertically against the finished wall.
Adjust the profile using a level. Use predrilled holes in the aluminum profile to mark holes
for drilling. Now drill holes in the wall and insert the Wall anchor (12) into the hole. See Fig
1 for details.
2. Apply silicone sealant along the holes on the wall. Push the Pivot retainer (8) into the top
and bottom sides of the Wall profile for glass door (1). Attach the wall profile to the wall
using Round head screws ST4.2×30 (17). See Fig 2 for details.
3. Locate the Glass profile for glass door (2). Push the upper Pivot assembly (7) into the
top groove of the Glass profile for glass door (2); then secure it and the profile with Flat
head screws ST4.2×25 (16) and M4×16 bolt (13). Repeat the same steps for the bottom
Pivot assembly. See Fig 3 for details.
NOTE: The Back plate (K) of the Pivot assembly (7) should face inside of your shower.
Please note it on Fig 3.
4. Push the assembled Glass profile for glass door (2) into the groove of the Wall profile
for glass door (1). Secure the upper Pivot assembly (7) and the upper Pivot retainer (8)
using Socket head screw M6×12 (18). See Fig 4 for details.
5. NOTE:
Please note the Glass door (3) is very heavy; you will need help of 1-2 people to
hold
this door for you during next step.
Your Glass door has 2 cuts for the pivot assembly. The deeper cut should be on
the top.
Remove the Bolts (L) and Back plates (K) from the Pivot assembly (7); then install the
Glass door (3) to the Pivot assembly. Make sure the rubber gaskets are in between the
glass and the metal parts. Secure tide the Glass door to the Pivot assembly. See Fig 5 for
details.
6. Install Handle (6) onto the Glass door (3). See Fig 6 for details.
NOTE: If your shower door requires only single glass door installation, you only need
to assemble parts from Packing List A and follow steps 7-14. However if your door
requires the glass door and stationary glass installation, you will need to use parts from
Packing List A and Packing List B and continue your installation with Step 15.
7. Push the Glass profile (4) into the Wall profile (5) and push the Anti-water strip (10) into
the groove of the glass profile. Close the glass door against the Anti-water strip (10) (Fig
7/3) to find the position of the wall profile. (You can pull the Glass profile from the Wall
profile to adjust width). Mark the position of the Wall profile on the wall. See Fig 7/1,2,3 for
details.
8. Pull out the Glass profile with Anti-water strip inserted into it from the wall profile. Use
predrilled holes in the aluminum profile to mark holes for drilling. Now drill holes in the wall
and insert the Wall anchor (12) into the holes. Apply silicone sealant along the holes on
the wall. Attach the Wall profile (5) to the wall using Flat head screws ST4.2×30 (17). See
Fig 7 for details.
9. Push the Glass profile (4) with the Anti-water strip (10) into the Wall profile (5).
10. Adjust the width of your door by pulling out the Glass profiles (2) and (4) if it necessary for
size of your door. Adjust the Glass door using a level and tighten in place with the Socket
head screw M6×12 (18). Close the glass door and make sure that there is 1/16" - 1/8" gap
between the glass door and the anti-water strip. See Fig 8.
11. Drill holes in Glass profile for glass door (2) through the Wall profile for glass door (1).
Secure the Wall profile for glass door (1) and the Glass profile for glass door (2) with
Rev. 1 .5
5