ANDI AFPH305LX Podręcznik użytkownika - Strona 2

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Piekarnik ANDI AFPH305LX. ANDI AFPH305LX 7 stron. Installation & servicing

Drukuj stronę

ENVIRONMENTAL WARNING

Waste packsging

Do not throw the packaging of your appliance into the dustbin, but pick

out the different materials (e.g. foil, paperboard, polystyrene) according

to the local rules for rubbish elimination.

• This appliance must be only be used for the purmpose of domestic cooking.

RECORD HERE FOR EASY REFERENCE

Model

Colour

Serial Number

Installation Date

Dealer's Name and Address

Important

Your new appliance has been manufactured to meet international standards.

This does not eliminate however, the obvious fact that an appliance

becomes hot with use and will retain heat even after you have stopped

cooking. We would therefore advise you to take extra care when using

and cleaning the appliance. Babies, toddlers and young children should

not be allowed near the appliance at any time. If and when the younger

members of your family are allowed into the kitchen, we strongly advise

that they are kept under supervision at all times.

Please keep these instructions for use close at hand and available to

anyone other than yourself who may use the appliance. By following the

recommendations made in these instructions you will be able to make

best possible use of your new appliance.

Warning

* The appliance is not intended for use by young children or infirm

persons without supervision.

* Young children should be supervised to ensure that they do not play

with the appliance.

* During use the appliance becomes hot. Care should be taken to avoid

touching heating elements inside the oven.

* WARNING: Ensure the appliance is switched off before replacing the

lamp to avoid the possibility of electric shock.

2 0

FITTING DIMENSIONS

Fig. 2

INSTALLING THE APPLIANCE

Installation should be carried out according to the instructions by a professionally

qualified person.

The manufacturer declines all responsibility for any damage to persons, animals

or things due to a wrong installation.

FITTING THE APPLIANCE

Fit the appliance into its surround (beneath a work-top or above another

appliance) by inserting screws into the 4 holes that can be seen in the frame

of the oven when the door is open.

Fig. 3

For the most efficient air circulation, the oven should be fitted according to

the dimensions shown in fig.1-2 of page 2.

The rear panel of the cabinet must be removed so that air can circulate freely.

The panel to which the oven is fitted should have a gap of at least 70 mm at

the rear.

NB: where ovens are to be matched with hobs, it is essential to follow

the instructions contained in the booklet supplied with the other

appliance.

IMPORTANT

For a built-in oven to work well the cabinet must be of the right type. The panels

of the adjoining furniture should be heat resistant. Particularly when the adjoining

furniture is made of veneered wood, the adhesives should be able to withstand

a temperature of 120°C. Plastic materials or adhesive which cannot withstand

this temperature will become deformed or unstuck.

To comply with safety regulations, once the appliance has been fitted it should

not be possible to make contact with the electrical parts. All parts which offer

protection should be fixed in such a way that they cannot be removed without

the use of a tool.

Fig. 1

Fig. 4

CLEANING AND MAINTENANCE

Wait until the appliance has cooled down before attempting to clean it.

Disconnect it from the power supply, either by pulling the plug out or switching off the power supply at the mains. Clean enamelled, chromed or

painted parts with warm water and soap, or non-corrosive liquid detergent.

Clean stainless steel parts using methylated spirit of a suitable commercially produced solution.

Clean aluminium panels or edges with cotton wool or with a cloth soaked in vaseline or a seed-based oil. Clean and then go over it with methylated

spirit. Never use abrasives, corrosive detergents, bleaches or acids for cleaning the oven.

Do not leave corrosive or acidic substances (lemon juice, vinegar, etc.) on enamelled, painted or stainless steel parts.

NOTE:

A steam cleaner is not to be used for cleaning this appliance .

Removal of oven door (Fig.12)

To make cleaning easier, remove the oven door as follows: insert hook

A (fig.12) in hinge slot B. Half open the door and, using both hands, pull

the door towards you untill it becomes unhooked. To refit the door, carry

out the same operation in reverse, taking care to introduce the two sectors

C correctly.

Removal of oven door ( fixed fulcrum )

In-depth cleaning of the oven becomes more convenient

if the door is removed following the instructions below:

Completely open the door and press it down gently (fig. 12A ) to allow

the hooks "A" of the hinge to locate inside the cavity "B" (fig. 12B).

Using both hands, pull the door towards you until it comes off the oven.

To replace the door, reverse the above procedure.

Self-cleaning panels (optional) (fig.13)

If the oven is fitted with self-cleaning panels, at normal cooking temperatures

the catalytic enamel helps transform grease splashes into a light dust.

This dust can be removed with a damp sponge when the oven has cooled

down. This helps keep the surface of the enamel porous and ensures

maximum cleaning efficiency. The self-cleaning panels and the shelves

frame are very easy to remove. The shelves holder frame is hooked on

to three catches. Simply press the catches down slightly to remove the

frame (fig.13A). This will also release the self-cleaning lateral panel

(fig.13B). To release the rear self-cleaning panel (which also acts as the

fan guard), refer to fig. 13C. In some models these three panels are not

installed, and the self-cleaning coating is on the oven side walls.

Install shelves by locating them in the horizontal guide rails on

the oven walls.

The raised portion of the shelf is to be facing the rear wall of the

oven.

Oven light (fig.14)

The oven bulb is a special kind which is resistant to high temperatures.

Replace it in the following way: disconnect the oven from the power supply,

either by pulling the plug out or by switching off the power supply at the

mains; remove the protective glass (A) and replace the burnt out bulb with

one of the same type. Replace the protective glass.

Important: if you decide not to use the oven any more, it should be

made inoperable by cutting the power supply cable, after unplugging

it from the power supply. Disused appliances can be a safety risk as

children often play with them. For this reason it is advisable to make

the oven safe.

Fig. 5

B C

Fig. 12

Fig.12A

Fig.12B

Fig. 13

T300°C

Fig. 14