Bosch 8-LI Professional Oryginalna instrukcja obsługi - Strona 8
Przeglądaj online lub pobierz pdf Oryginalna instrukcja obsługi dla Wiertarka Bosch 8-LI Professional. Bosch 8-LI Professional 13 stron. Jigsaw and sabre saw
Również dla Bosch 8-LI Professional: Oryginalna instrukcja obsługi (10 strony), Oryginalna instrukcja obsługi (39 strony), Oryginalna instrukcja obsługi (13 strony), Oryginalna instrukcja obsługi (8 strony)
Drukuj stronę
OBJ_BUCH-1066-001.book Page 18 Thursday, December 3, 2009 9:10 AM
18 | English
Noise/Vibration Information
Measured sound values determined according
to EN 60745.
Typically the A-weighted noise levels of the
product are: Sound pressure level 87 dB(A);
Sound power level 98 dB(A). Uncertainty
K =3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) deter-
mined according to EN 60745:
Impact tightening of fasteners of the maximum
capacity of the tool: Vibration emission value
2
a
=9 m/s
, Uncertainty K =1.5 m/s
h
The vibration emission level given in this infor-
mation sheet has been measured in accordance
with a standardised test given in EN 60745 and
may be used to compare one tool with another.
It may be used for a preliminary assessment of
exposure.
The declared vibration emission level repre-
sents the main applications of the tool. However
if the tool is used for different applications, with
different accessories or poorly maintained, the
vibration emission may differ. This may signifi-
cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibra-
tion should also take into account the times
when the tool is switched off or when it is run-
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the to-
tal working period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that
the product described under "Technical Data" is
in conformity with the following standards or
standardization documents: EN 60745 accord-
ing to the provisions of the directives
2004/108/EC, 98/37/EC (until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009).
2 609 140 699 | (3.12.09)
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
26.10.2009
2
.
Assembly
Battery Charging (see figure A)
Use only the battery chargers listed on the
accessories page. Only these battery charg-
ers are matched to the lithium ion battery of
your power tool.
Note: The battery is supplied partially charged.
To ensure full capacity of the battery, complete-
ly charge the battery in the battery charger be-
fore using your power tool for the first time.
The lithium ion battery can be charged at any
time without reducing its service life. Interrupt-
ing the charging procedure does not damage the
battery.
The lithium ion battery is protected against
deep discharging by the "Electronic Cell Protec-
tion (ECP)". When the battery is empty, the ma-
chine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
WARNING
chine has been automatically switched off. The
battery can be damaged.
To remove the battery 7 press the unlocking but-
tons 6 and pull out the battery downwards. Do
not exert any force.
The battery is equipped with a NTC temperature
control which allows charging only within a tem-
perature range of between 0 °C and 45 °C. A
long battery service life is achieved in this man-
ner.
Observe the notes for disposal.
Dr. Eckerhard Strötgen
Head of Product
Certification
Do not continue to press the
On/Off switch after the ma-
Bosch Power Tools