Andis D-4 Skrócona instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Trymer Andis D-4. Andis D-4 2 stron. Rechargeable horse trimmer
Również dla Andis D-4: Specyfikacja (2 strony), Lista części (1 strony), Specyfikacje (1 strony)

Drukuj stronę

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be

followed, including the following: Read all instructions before using the

Andis clipper/trimmer.

DANGER:

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug

immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or be pulled into a tub

or sink. Do not place in or drop into water or other liquid.

4. Except when charging, always unplug this appliance from the electric

outlet immediately after using.

5. Unplug this appliance before cleaning, removing or assembling parts.

WARNING:

To reduce the risk of burns, fire electric shock,

or injury to persons:

1. An appliance should never be left unattended when plugged in.

2. Close supervision is necessary when this appliance is used by, on or

near children or individuals with certain disabilities.

3. Use this appliance only for its intended use as described in this

manual. Do not use attachments not recommended by Andis.

4. Never operate this appliance if it has a damaged cord or plug, if it is

not working properly, if it has been dropped or damaged, or dropped

into water. Return the appliance to an Andis Service Center for

examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol (spray) products are

being used or where oxygen is being administered.

8. Do not use this appliance with a damaged or broken blade, as injury to

the skin may occur.

SAVE THESE INSTRUCTIONS

THIS PRODUCT INTENDED FOR PROFESSIONAl USE.

OPERATING INSTRUCTIONS

Please read the following instructions before using your new Andis cordless

clipper/trimmer. Give it the care that a fine precision built instrument deserves

and it will give you years of service.

READ THE FOllOWING BEFORE CHARGING THIS

ClIPPER/TRIMMER

Remove Andis clipper/trimmer and charger from carton and plug into 120V or

230V outlet as identified on the bottom of the charger, or on the outside of the

carton. Note that the clipper/trimmer ON/OFF switch must be in the OFF

position for the battery to charge. Place cordless clipper/trimmer into form

fitting pocket in charger. The unit is "keyed" to fit one way only. The green light

on the charger will turn on. The clipper/trimmer has electrical contacts that

touch electrical contacts in the charger. The weight of the unit will give

sufficient contact. The clipper/trimmer is not charged at the factory. Please

recharge clipper/trimmer for 12 hours (overnight) before first use for

maximum performance.

You may keep the clipper/trimmer in the charger when not in use. The charger

will maintain the battery at full charge and the green light will stay on. The unit

has a Nickel Metal Hydride battery that cannot be damaged by overcharging.

However, we recommend that the charger be unplugged if the clipper/trimmer

won't be used for seven or more days.

PlEASE NOTE: Nickel Metal Hydride batteries have less "Memory Effect" than

Nickel Cadmium batteries. Memory Effect is caused by repeated short uses of

the clipper/trimmer, followed by charging. The battery never fully discharges

and, therefore, "forgets" how much energy it can store. In order to maximize

the performance of your Nickel Metal Hydride battery, please follow these steps:

1. Oil blade. Turn clipper/trimmer on and allow it to run until the blade slows

significantly. It is not necessary to let the blade stop completely.

2. Turn clipper/trimmer off. Charge overnight.

3. Conduct the above exercise every sixty days.

FAIlURE TO CHARGE:

1. Make sure voltage is present at the wall outlet (confirm with an appliance you

know is working).

2. Check the alignment of the contacts between the clipper/trimmer and those

in the charger. The contacts in the charger should be centered in the small

openings, and protrude slightly into the charger pocket. Disconnect power to

the charger, and correct if necessary.

3. Make sure contacts on both charger and clipper/trimmer are clean.

Disconnect power to the charger and rub contacts with a pencil eraser until

shiny. Wipe contacts and brush off remaining dust with a soft dry cloth.

4. If failure to charge still exists, return trimmer to Andis or an Andis Authorized

Service Station for examination and repair or replacement.

ATTENTION: The product you have purchased contains a

rechargeable battery. The battery is recyclable. At the end of its

useful life, under various state and local laws, it may be illegal to

dispose of this battery into the municipal waste stream. Check

with your local solid waste officials (or call 1-800-822-8837) for

details in your area for recycling options or proper disposal.

USER MAINTENANCE

The internal mechanism of your clipper/trimmer has been permanently

lubricated at the factory. Other than the recommended maintenance described

in this manual, no other maintenance should be performed, except by

Andis Company or an Andis Authorized Repair Service Station.

CARE AND SERVICING OF YOUR ANDIS TRIMMER BlADES

(Trimmer shown in diagrams may vary from the one that you have.)

Blades should be oiled before, during, and after

each use. If your trimmer blades leave streaks or

slow down, it's a sure sign blades need oil. The

clipper/trimmer should be held in a position

shown in Diagram A to prevent oil from getting

into motor. Place a few drops of Andis Clipper Oil

on the front and side of the cutter blades (See

DIAGRAM A

Diagram B). Wipe excess oil off blades with a soft

dry cloth. Spray lubricants contain insufficient oil

for good lubrication, but are an excellent clipper

coolant. Always replace broken or nicked blades

to prevent injury. You can clean the excess hair

OIL

from your blades by using a small brush or worn

out tooth brush. To clean the blades we suggest

to immerse the blades only into a shallow pan of

Andis Clipper Oil, while the clipper is running.

Any excess hair and dirt that has accumulated

DIAGRAM B

between the blades should come out. After

cleaning, turn your clipper/trimmer off and dry blades with a dry cloth and start

clipping again.

REPlACEMENT (REMOVAl) OF BlADE SET

Your Andis clipper/trimmer consists of a preset tension assembly on the blade

set. To remove blade set from your clipper/trimmer, remove from charger base.

Turn the clipper/trimmer upside down so teeth of blades are facing down. You

may wish to set the clipper on a flat surface while performing these operations.

Using a phillips type screwdriver, unscrew the two blade screws as shown in

Diagram C. Remove blade set from clipper/trimmer. Install new blade set,

making sure the blade yoke cradles the armature pin on clipper/trimmer (See

Diagram D). There is no need to adjust blade tension before use, as tension has

been preset at the factory. Align screw holes of blade set to screw inserts on

clipper/trimmer housing. Replace the screws. Before tightening down blade

screws, check alignment of blade set to housing, making sure that they are

parallel. Tighten down screws.

ARMATURE

STAINLESS

BLADE

YOKE

BLADE SCREWS

DIAGRAM C

DIAGRAM D

ATTACHING THE ClIPPER COMBS

(Some models do not have attachment combs)

The clipper comb blade attachments mount easily. Just

snap them on. Snap them off. Combs help guide hair to

cutting blades and give you precise control of hair lengths.

Each comb allows a different length of cut which is

indicated on the combs: 1/16", 1/8", 1/4", and 3/8".

You can always set blades for a coarser cut by attaching any of the four snap-on

blade attachments.

OIL

To use a blade attachment, slip the cutter blade teeth into blade attachment.

Snap blade attachment down, they snap on and off easily. These attachments

guide hair into the clipper blades and give you precise control of hair lengths.

OIL

The length of trim is indicated on the blade attachment: 1/16", 1/8", 1/4", and 3/8".

Use the following chart to find the approximate lengths of cut. Different blade

angles in relation to the skin, thickness and texture of the hair will vary the

cutting length.

ClIPPING GUIDE

Description

Clipping Direction

Standard Andis Blade

With hair grain

Against hair grain

1/16" Blade Attachment

With hair grain

Against hair grain

1/8" Blade Attachment

With hair grain

Against hair grain

1/4" Blade Attachment

With hair grain

Against hair grain

3/8" Blade Attachment

With hair grain

#3 1/2

Against hair grain

THE PRElIMINARIES

1. To make cutting smoother and easier, always start with a clean head of

hair. Wash the hair with your favorite shampoo. Rinse. Repeat. We also

recommend using a hair conditioner to untangle snarls and leave hair soft

and easy to manage.

2. When drying the hair, just use a towel so as not to dry it too thoroughly.

Leaving it damp makes the hair easier to work with.

FACTORY REPAIR SERVICE

When the blades of your Andis clipper/trimmer become dull after repeated use,

it is advised to purchase a new set of blades available through your Andis Supplier

or through an Andis Authorized Repair Station. If you wish your clipper/trimmer

to be serviced as well, it should be carefully packed and mailed either Parcel

Post Insured, or U.P.S. to any Andis Service Center.

Approximate

length of Cut

1/16"

1/32"

3/16"

1/16"

1/4"

1/8"

3/8"

1/4"

1/2"

3/8"