Electrolux EHC644BA Podręcznik użytkownika - Strona 16
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Hob Electrolux EHC644BA. Electrolux EHC644BA 20 stron. Ceramic glass hob
Drukuj stronę16
INSTALLATION INSTRUCTIONS
WArNINg!
This must be read! The laws, ordinances, directives
and standards in force in the country of use are to
be followed (safety regulations, proper recycling in
accordance with the regulations, etc.)
ImPOrTANT!
Installation may only be carried out by a qualified electrician.
The minimum distances to other appliances and units are to
be observed.
Anti-shock protection must be provided by the installation, for
example drawers may only be installed with a protective floor
directly underneath the appliance.
The cut surfaces of the worktop are to be protected against
moisture using a suitable sealant. The sealant seals the
appliance to the work top with no gap. Do not use silicon
sealant between the appliance and the work top. Avoid
installing the appliance next to doors and under windows.
Otherwise hot cookware may be knocked off the rings when
doors and windows are opened.
WArNINg!
risk of injury from electrical current.
• T he electrical mains terminal is live.
• M ake electrical mains terminal free of voltage.
• F ollow connection schematic.
• O bserve electrical safety rules.
• Ensure anti-shock protection by installing correctly.
• T he appliance must be connected to the electrical
supply by a qualified electrician.
• L oose and inappropriate plug and socket connections
can make the terminal overheat.
• H ave the clamping connections correctly installed by a
qualified electrician.
• Use strain relief clamp on cable.
WArNINg!
The surface temperature exceeds 95°C. To avoid a
hazard, underbench access must be restricted.
Electrical Connection
Before connecting, check that the nominal voltage of
the appliance, that is the voltage stated on the rating
plate, corresponds to the available supply voltage. Also
check the power rating of the appliance and ensure that
the wire is suitably sized in accordance with local wiring
rules to suit the appliance power rating. The rating plate
is located on the lower casing of the hob. The heating
element volt- age is AC230V~. The appliance also works
perfectly on networks with AC220V~ or AC240V~. means
for disconnection must be incorporated in the fixed
wiring in accordance with local wiring rules.The hob is
to be connected to the mains using a device that allows
the appliance to be disconnected from the mains at all
poles with a contact opening width of at least 3 mm, eg.
automatic line protecting cut-out, earth leakage trips or
fuse. If this appliance's mains cable is damaged, it must
be replaced by a special cable (type H05BB-F Tmax
90°C; or higher). The latter is available from the Customer
Care Department. The connection must be carried out
as shown in the diagram. The connecting links should be
fitted according to the appropriate connection diagram.
The earth lead is connected to terminal. The earth lead
must be longer than leads carrying electric current. The
cable connections must be made in accordance
with regulations and the terminal screws tightened
securely. Finally, the connecting cable is to be secured
with the mains cable cleat and the covering closed by
pressing firmly (lock into place). Before switching on for the
first time, any protective foil or stickers must be removed
from the glass ceramic surface.
WArNINg!
Once connected to the mains supply check that all
cooking zones are ready for use by briefly switching
each on in turn at the maximum setting.
• A duplicate rating label is supplied with this unit. For
easy identification of this unit after installation, stick it to
a readily available surface adjacent to the cooktop.
Sticking on the seal
• C lean the worktop around the cutout area.
• S tick the single-sided adhesive sealing tape provided
on the underside of the hob around the outside edge
ensuring that it is not stretched. The two ends of
the tape should join in the middle of one side. After
trimming the tape (allow it to overlap by 2-3 mm), press
the two ends together.
ImPOrTANT!
The cut-out section in the worktop is illustrated in the
drawing with the dimensions 560 x 490 / 880 x 490 mm.
The appliance can also be built into a shorter cut-out
section with the dimensions 560 x 485 / 880 x 485 mm.