Atlantic Heater Instrukcja obsługi - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Grzałka Atlantic Heater. Atlantic Heater 8 stron.

Drukuj stronę
1) Description of the control unit :
  Mode cursor.
2) Fixing the comfort temperature
The comfort setting is the temperature that is preferred during times the rooms is occupied.
a) Slide the switch  cursor to
b) Ajust the control dial  to the preferred position, the heating light V1 indicates if the temperature drops below the preferred
on the control dial .
c) Wait a few hours for the temperature to stabilise.
d) If the setting is satisfactory (if necessary use a thermometer to check), mark the position for future use.
e) If the setting is not satisfactory, adjust it and start again from point c.
3) Fixing the Eco temperature :
The Eco setting reduces the temperature setting by 3 to 4 degrees. The Eco setting can be used when the room is unoc-
cupied for more than 2 hours.
a) Slide the switch  to .
b) Adjust the control dial  to the preferred position, the heating light V1 indicates if the temperature drops below the
temperature set on the control dial .
c) Wait a few hours until the temperature stabilizes.
Note : When switching n°1 (on the picture) is set on Programming system (clock symbol) with the PassProgram
On/Off, please refer to paragraph n°8.
4) Frost-Free mode
This mode is used to keep the temperature at approximately 7°C in the room when you are absent from the house for
a prolonged period (i.e. more than 24 hours).
a) Set the  switch on
5) The heating indicator : V1
This light comes on when the heating element is working. It may flash when the temperature has stabilised.
6) Locking the controls :
It is possible to lock or limit use of the  control dial and lock the  switch to prevent unauthorised manipulation of
the panel heater (children, etc.).
a) Unhook the panel heater from its wall mounting.
b) Remove the pins P on the back of the thermostat casing.
c) Select position B to lock the control dial or position L to limit the amount it can be turned. Position M blocks the switch
for Electronic Model.
7) Using the pilot wire :
The product with pilot wire can receive the following signals from a master unit :
- comfort (temperature of  control dial)
- eco (comfort temperature -3°C to -4°C)
- frost free (approximately 7°C)
- off.
Put the switch  to the programming mode
The product must be connected through the pilot wire to a programming control or a product equipped with pass program
system in order to use these different modes. You can control several convectors with a single programmer or a product
equipped with pass program system.
Warning: When the programme turns to Frost Free or Off in the main programming system or using a Pass Program system,
these functions will override the manual switch of the Panel Heater.
8) Using the On/Off PassProgram system. Ref 602019
When using programming mode (clock symbol) with the on/off pass program system (interface + timer), the moon symbol
on the timer refers to the off mode (no heating).
Important : If the timer (602019) is set to off, this function will override the slide switch 1 modes (eco, comfort & frost free)
on the heater.
- There is no point in setting maximum heating, the room temperature will not rise any quicker.
- When you air the room, disconnect the panel heater by putting the  switch to off
- If you leave the room for several hours slide the switch  to  eco position.
Absence for: less than 2 hours, set the cursor  switch knob to moon .
2 to 24 hours, either you can lower the control dial  by two graduations, select eco mode  or switch to off
- If you have several units in a room, let them operate simultaneously. This will give you a more uniform temperature without
increasing electricity consumption.
USING THE PANEL HEATER
  Temperature adjustment control dial.
.
.
.

RECOMMENDATIONS FOR USE

V1  Heating indicator light
.
.