3M 3MRO501 Instrukcja instalacji i obsługi - Strona 10
Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Systemy filtracji wody 3M 3MRO501. 3M 3MRO501 12 stron. Pro reverse osmosis drinking water system
Drukuj stronę
II. Operation & Maintenance Instructions
Failure to install, operate or maintain your filter system in accordance with these use instructions or
any other installation or use instructions accompanying this product may result in product failure and
property damage, including water leakage and will void warranty.
A. IMPORTANT WATER QUALITY ASSURANCE
Reverse Osmosis drinking water filtration systems contain
treatment components that are critical for the effective reduction of
Total Dissolved Solids (TDS) as well as some inorganic chemical
contaminants. It is strongly recommended that the user test the water
periodically (every six (6) months minimum) to verify that the system is
performing satisfactorily. Routine maintenance is necessary in the form
of sediment, granulated carbon filter and membrane module, based on
the following guidelines:
•
Sediment Replacement Filters, Granulated Carbon Replacement
Filters & Carbon Block Replacement Post-Filters: Change every
twelve (12) months, at the rated capacity or sooner if a noticeable
reduction in flow rate occurs.
•
Pro RO Membrane Replacement Module: Change it as required
based on 90 Percent Rejection. The recommended maximum
service life is thirty-six (36) months, at the rated capacity or
sooner if a noticeable reduction in flow rate occurs.
B. REPLACING THE FILTERS
NOTE: It is essential that the filters be installed in the correct
location. Use the icon coded labels to match the filter cartridges with
their corresponding filter head.
The life of the filters generally depends on the local water conditions
(i.e., sediment, rust and/or chlorine levels) while the life of the post-filter
is generally determined by the length of service.
When to Replace the Sediment Replacement Filter
•
Every twelve (12) months
or sooner depending on local water conditions.
•
A noticeable decrease in water production is an indication that the
filter requires changing.
When to Replace the Granulated Carbon Replacement Filter
The granulated carbon replacement filter reduces free chlorine in the
feed water supply to protect the TFCM membrane from chlorine attack. To
find out the chlorine level in a water supply, call the public water supplier.
When to Replace the Carbon Block Replacement Post-Filter
•
If the filter is being used to control tastes and odors, replace it every
twelve (12) months or sooner depending on local water conditions.
How to Replace the Filters (See Fig. 9 for filter identification)
1)
Lift up on the faucet handle and close the cold water feed valve and
unplug the booster pump transformer. Wait five (5) minutes for the
filtration assembly to completely depressurize.
2)
Remove cover.
3)
Twist the existing filter 1/4 turn to the left so that the ears on the
filter are able to disengage from the head. Firmly pull the filter from
the head. It may be necessary to twist the filter slightly from side
to side to help free it.
4)
Remove the new replacement filter from its protective wrap. (Double
check to see that it is the correct replacement by comparing the labels.)
5)
Remove the protective sanitary cap from atop the replacement filter.
6)
Ensure both o-rings are present on the replacement filter and are
seated into grooves; moisten o-rings with water. DO NOT use any
petroleum products to lubricate the o-rings.
7)
Line up the filter ears, insert the filter and push it into the head until it
is fully seated. Twist the filter 1/4 turn to the right to lock it into place
(See Fig 6).
8)
Open the cold water feed valve, plug in the booster pump
REQUIREMENTS
transformer and carefully check for leaks.
9)
Pro RO System Flush Instructions:
Sediment & Granulated Carbon Replacement Filters — Close
tank. Lift the faucet handle and flush at least two (2) gallons of
water through system (approximately 10 minutes).
Carbon Block Post-Filter — Open tank. Lift the faucet handle
and flush at least two (2) gallons of water through post-filter
(approximately 30 minutes with tank empty or 5 minutes with
tank full). It may be necessary to continue flushing until water
becomes clear.
•
Replacement of filters will result in the need to sanitize the filtration
system and/or the storage tank. Please refer to Section D "Sanitizing
the Pro RO System" on page 11 for further instructions.
C. REPLACING THE Pro RO MEMBRANE MODULE
The life of the Pro RO membrane module depends on the local
water conditions and proper maintenance, e.g., regular module changes.
Under typical conditions, the Pro RO membrane module life is thirty-
six (36) months or sooner. Unlike the replacement filters, the Pro RO
membrane module life is not determined by the amount of water used
because of its self-cleaning feature.
How to Replace the Pro RO Membrane Module
1)
Lift up on the faucet handle, close the cold water feed valve and unplug
the booster pump transformer. Wait five (5) minutes for the filtration
assembly to completely depressurize.
2)
Remove cover.
3)
Make sure that there is some slack in the red SFC tubing
connected to the fitting at the bottom of the Pro RO membrane
module. Twist the module 1/4 turn to the left (counterclockwise)
so that the tubing connection is accessible.
4)
Remove existing red SFC tubing from faucet adapter and membrane
module by depressing the small collet and pulling the tubing away
from the fittings.
5)
Firmly pull the module away from the head.
necessary to twist the module slightly from side to side.)
6)
Remove the new Pro RO membrane module from its protective
wrap. (Double check to see that it is the correct replacement by
comparing the labels.)
7)
Remove the sanitary plastic cap atop the module.
8)
Ensure both o-rings are present on the replacement filter and are
seated into grooves; moisten o-rings with water. DO NOT use any
petroleum products to lubricate the o-rings.
9)
Connect the new red SFC reject tubing (supplied with replacement
membrane module) by inserting it into the fitting at the bottom of
the new Pro RO membrane module as far as it will go, and into the
faucet adapter. Line up the module ears, insert the module and
push it into the head until it is fully seated. Twist the module 1/4
turn to the right (clockwise) to lock it into place.
10) Open the cold water feed valve, plug in the booster pump transformer
and carefully check for leaks. Carefully inspect the fitting at the bottom
of the new Pro RO membrane module.
11) For sanitization of Pro RO system please follow instructions below
in Section D.
12) Flush membrane module - refer to Section M, Step 1 and 2 on
page 8.
10
IMPORTANT NOTES
(It may be