Atlantic Technology IWTS-14 SR Instrukcja obsługi - Strona 7
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Głośniki Atlantic Technology IWTS-14 SR. Atlantic Technology IWTS-14 SR 8 stron. High performance in-wall surround speakers
Drukuj stronę
Instruction Manual
Installing the Speaker Assembly
screws, which will cause the attached clamps to rotate and position them-
selves properly behind the wall.
Continue to tighten until the speaker is snug in the wall. You want the bezel
to conform to the wallboard, and the frame not to rattle from the speaker's
vibration, but be very careful not to overtighten the screws.
It is strongly recommended that you hand-tighten the mounting screws
the final few turns (after using an electric screwdriver set to "low
torque") to avoid the possibility of damaging the frame.
Painting the Speaker Assembly
The white plastic frame and the metal grille may be left as is, or painted to
match your décor. To paint the frame, place the included Paint Shield over
the drivers, then carefully spray paint with a plastic-compatible paint. To
paint the grille, first remove it from the speaker, then spray using a slightly
thinned paint or with two very light coats.
The clamping mechanism
allows the wall material to
range from ½" to 1½" (13 to
38 mm) in thickness. There
must be a minimum depth
behind the wall face of 3
⁄
"
5
8
(92 mm). As noted above, be
sure to keep the top and bot-
tom of the cutout at least 1½"
(38mm) away from obstruc-
tions, as the rotating clamps
will not operate properly if
you don't.
Insert the speaker into the
cutout and using a level or
square carefully align it so it
is level. Tighten the mounting
Speaker Connection
Strip about ½" (13 mm) of insulation from the connecting wires. Connect
them to the appropriate push terminal, being careful to observe polarity
(positive to the red terminal, negative to the black terminal).
Specifications
Model
IWTS-30 SR
THX Certification
THX Ultra
Type
2-way Dipole/Bipole
Switchable
Drivers
Woofer (2) 5¼" (135mm) GLH
Tweeter (2) 1" (25mm) soft dome
Frequency Response
80Hz – 20kHz ±3dB
Nominal Impedance
6 Ohms
Crossover Frequency
3500Hz
Sensitivity
87dB
Recommended
25 – 150 Watts RMS
Amplifier Power
Overall Dimensions
15
⁄
x 12
5
1
8
(W x H x D)
397 x 308 x 96mm
Cutout Dimensions
14¼ x 10¾"
(W x H)
362 x 273mm
Weight (ea)
9lbs; 4.1kg
Graphite Loaded Homopolymer
§
Specifications are those in effect at the time of printing. Atlantic Technology reserves the right
to change specifications or appearance at any time without notice.
THX, and THX Select are trademarks of THX Inc. Dolby Digital, 5.1, Dolby Stereo and Dolby Pro
Logic are trademarks of Dolby Laboratories Licensing Corporation. DTS is a registered trade-
mark of DTS Technology.
Speaker Wiring
IWTS-14 SR
NA
2-way Dipole/Bipole
Switchable
(2) 4½" (115mm) GLH
§
(2) 1" (25mm) soft dome
100Hz – 20kHz ±3dB
6 Ohms
4000Hz
87dB
25-125 Watts RMS
⁄
x 3¾"
15
⁄
x 12
⁄
x 3¾"
5
1
8
8
8
397 x 308 x 96mm
14¼ x 10¾"
362 x 273mm
8lbs; 3.7kg
7
§