Atlas AH99-12ST Specyfikacje - Strona 2

Przeglądaj online lub pobierz pdf Specyfikacje dla Głośniki Atlas AH99-12ST. Atlas AH99-12ST 4 stron. High-performance, constant directivity, 8", 12", and 15", two-way, indoor/outdoor loudspeaker systems ah series
Również dla Atlas AH99-12ST: Broszura (10 strony), Instrukcja obsługi (12 strony), Instrukcja instalacji (12 strony)

Drukuj stronę

Technical Speciﬁcations

Power Rating:

Sensitivity 1 W / 1 M:

Frequency Response:

Dispersion:

Impedance:

Transformer Taps:

Height:

Width:

Depth:

Shipping Weight:

Driver Type:

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333

FAX (800) 765-3435

200 watts

101 dB SPL (70 Hz to 17 kHz

⁄

octave bands)

80 Hz - 15 kHz (±5 dB)

90° x 90°

8 Ω Nominal

7.5, 15, 30, & 60 watts

25.68" (652.27 mm)

22.06" (560.32 mm)

22.57" (573.28 mm)

136 lbs (61.69 kg)

1" HF and 12" LF

22.57"

(573.28 mm)

Architect & Engineer Speciﬁcations

Loudspeaker shall be Atlas Sound Model AH99-12ST or approved equal.

The loudspeaker system shall be a horn-loaded, 2-way design with a 12

inch paper cone and moisture resistant coating.

The loudspeaker system shall include a 12", horn loaded, cast frame

woofer and an integral, concentrically mounted 1" exit compression driv-

er coupled to a constant directivity high frequency horn. The three pole

(18dB/octave) dividing network shall have a crossover frequency of 1.6

kHz. The dividing network shall include a poly switch protection circuit

for the high-frequency component.

The loudspeaker system shall be capable of providing a sound dispersion

angle of 90˚ horizontal by 90˚ vertical in the 2 kHz octave band.

Rated power shall be 200 watts RMS based on EIA Standard RS-426B.*

Enclosure shall be UV-resistant, steel reinforced, low pressure injection

molded fiberglass and shall include a 3 stage multiple mesh filter system

for weather and rodent resistance: to include a 20GA perforated alumi-

num screen on front mouth assembly, a 100x100 weave stainless steel

mesh between HF horn and HF driver and a 100x100 weave stainless

steel mesh over 12" woofer. The loudspeaker shall include a stamped

and formed, 2 mm stainless steel powder coated mounting bracket

assembly for surface mounting and (3) M8 drop forged eyebolts for

suspension mounting two at the front and one at the rear to allow the

speaker system to be suspended and aimed using rated wire rope.

Sensitivity shall be 101 dB SPL (80 Hz to 15 kHz in

measured at a distance of one meter on axis with a one watt input half

space (2.83V).

Overall frequency response shall be 80 Hz to 15 kHz (±5 dB).

The input section located on the bottom rear of the loudspeaker shall be

via 7 position screw down terminal strip internally configured to allow

input to an internally mounted 70.7 V transformer with 7.5, 15, 30, & 60

watts taps and a by-pass jumper direct coupled to the speaker for nomi-

nal 8 Ω operation. The system connections shall be protected from the

elements by a screw affixed weather resistant cover.

Dimensions shall be: Height: 25.68" (652.27 mm)

* EIA test spectrum is applied for eight hours.

(This procedure provides a rigorous test of both thermal and

mechanical failure modes.)

��

14.65"

��

(372.11 mm)

Width: 22.06" (560.32 mm)

Depth: 22.57" (573.28 mm)

Weight: 136 lbs (61.69 kg)

AtlasSound.com

⁄

octave bands)

25.68"

��

(652.27 mm)

2/4