Atlas CP700 Instrukcja obsługi - Strona 10
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz Atlas CP700. Atlas CP700 16 stron. Commercial dual channel power amplifiers
Również dla Atlas CP700: Broszura (2 strony), Instrukcja obsługi (16 strony), Arkusz specyfikacji (2 strony), Broszura i specyfikacje (10 strony), Instrukcja obsługi (16 strony), Instrukcja obsługi (16 strony)
Drukuj stronę
CP400 & CP700 COMMERCIAL
POWER AMPLIFIER
Bridge Mono Configuration (Direct Coupled)
If higher power levels are required, the Atlas amplifier can be used in Bridge Mono mode, which utilizes
both channels of the amp across the speaker load.
With the amplifier turned OFF, move the rear mounted selector switch to the "Bridge" position and connect
the input signal to channel one. Connect your speaker load (4 and 8 Ω only) across the "+" terminals of
both channels, with channel 1 being positive and channel 2 being negative (Figure 7).
CAuTION: A high voltage potential exists across the two "+" speaker terminals when operating in
any Bridge Mode application!
CP700
Commercial
Power
Amplifier
Per Channel
Output Power
400 W / 4 Ohms
350 W / 70.7 V
AC100V-50/60Hz
To loudspeakers,
AC120V-50/60Hz
4 Ω minimum
AC230V-50/60Hz
AC240V-50/60Hz
25V, 70.7V, and 100V Transformer Output Wiring
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
For transformer coupled operation into high impedance loads, connect your loudspeaker leads to the
NO USER SERVICEABLE PARTS INSIDE
barrier strip connections labeled "Audio Transformer." Connect the speaker home runs as follows:
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
• 25V - Connect the positive speaker lead to the terminal labeled "100" and the negative speaker
lead to the terminal labeled "70" (Figure 8).
• 70.7V - Connect the positive speaker lead to the terminal labeled "70" and the negative speaker
lead to the terminal labeled "0" (Figure 9).
• 100V - Connect the positive speaker lead to the terminal labeled "100" and the negative speaker
lead to the terminal labeled "0" (Figure 10).
Note: Refer to page 6 of this manual to the paragraph entitled "Calculating Constant Voltage Loads" to
determine how many transformer coupled loudspeakers you can drive with the Atlas amplifier.
1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. •
©2008 ATLAS SOUND LP
CH-1
8, 4, and 2 Ohms
+
-
D I R . O U T P U T
+
BRIDGE
MONO
CH-2
8, 4, and 2 Ohms
+
-
D I R . O U T P U T
-
BRIDGE
MONO
POWER
CAUTION
Specifications are subject to change without notice
AtlasSound.com
Printed in U.S.A.
OWNER'S MANUAL
CH-1
AUDIO TRANSFORMER
0
70
100
I S O L . O U T P U T
-
+
-
+
70V
25V
- 100V +
CH-2
AUDIO TRANSFORMER
0
70
100
I S O L . O U T P U T
-
+
-
+
70V
25V
- 100V +
MADE IN CHINA
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
TELEPHONE: (800) 876-3333 • FAX: (800) 765-3435
Switch set
to "Bridge"
Figure 7
ATS002102 RevD 2/08
PP
10