Atlas FAP8CXT Specyfikacje - Strona 2
Przeglądaj online lub pobierz pdf Specyfikacje dla System głośników Atlas FAP8CXT. Atlas FAP8CXT 4 stron. Strategy series ii coaxial loudspeaker system
Drukuj stronęMounting Accessories
Mounting is simplified with Strategy Series
allow easy installation into drop tile or drywall ceilings with provided
tile bridge assembly. The tile bridge consists of (2) V-Rails and a C-Ring
assembly. The C-Ring can be attached to the rails with the screws
p rovided to extend support to the T-Bar grid in suspended ceiling
a pplications. Multiple hole locations are provided to allow the C-Ring to
be positioned to the outer edge of the tile if necessary.
For existing drywall applications the tile bridge C-ring and support rails
can be inserted into the hole cut for the FAP8CXT. For easy positioning
the V shaped support rails match the shape of the C-ring tabs for easy
maneuvering and location when working "blindly" above the deck. This
technique is recommended to distribute the weight of the system across
a wider area of the ceiling.
A uniquely designed "easy access" input panel on the side of the enclo-
sure allows conduit runs using flexible or rigid conduit. Below this cover
resides a detachable Phoenix style locking four-pole connector for field
wiring connection and pass-through.
The package includes an attractive press-fit grille, which nicely matches
contemporary architecture.
For new construction drywall ceiling applications, the optional FAP82-TR
trim ring is available. This unit provides a marked location for drywall
installers to cut around, essentially reserving the desired location in the
ceiling until final installation of FAP8CXT is completed. Mounting holes
are provided to accommodate 16" or 24" OC stud/joist mounting.
With the FAP8CXT, Atlas Sound has addressed pendant mounting for
open ceiling applications. An eyebolt assembly is incorporated into the
package allowing suspension of the FAP8CXT with load rated cable, "all
thread" or other load rated hardware. The enclosure is finished white to
match the bezel ring for better blend in open ceiling applications. Please
note that the enclosure/bezel ring may also be painted to accommodate
custom finishes when required.
SPEAKER SYSTEMS SUSPENDED OVERHEAD POSE A RISK
OF SERIOUS INJURY OR DEATH IF THEY FALL.
Overhead suspension of any object (rigging) is inherently dangerous.
It poses a substantial risk of injury or death to both those persons per-
forming the installation and those persons who may later occupy the
space under the suspended objects. You may be held liable for any injury
or damages which may be alleged to result from improper installation.
IF YOU ARE NOT EXPERIENCED IN RIGGING OR SUSPENSION OF
SPEAKER SYSTEMS, OR IF YOU HAVE ANY DOUBT THAT YOU ARE
QUALIFIED TO INSTALL SUSPENDED SPEAKER SYSTEMS, DO NOT
PROCEED.
Instead, you should obtain the services of properly qualified personnel to
complete the installation.
NEVER SUSPEND THE SPEAKER SYSTEM BY ANY
ATTACHMENT EXCEPT THE PROVIDED SUSPENSION POINT.
The eyebolt must be used with an auxiliary support cable in drop tile
installations. NOTE: it is MANDATORY that the secondary support be uti-
lized in drop ceilings for safety and seismic considerations).
1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.
TELEPHONE: (800) 876-3333
FAX (800) 765-3435
style "dog leg" tabs that
®
Architects and Engineers Specifications
The loudspeaker system shall be Atlas Sound FAP8CXT. System shall
include a high performance 8" coaxial loudspeaker, ported bass reflex
enclosure and press-fit grille for conventional ceiling installation.
Frequency response for the system shall be 60 Hz to 15 kHz (±5 dB).
Sensitivity shall be 92 dB average.
The 150 watt loudspeaker systems shall have a 8.25" (310 mm) woofer
constructed with polypropylene cone and a 1" (25 mm) titanium dia-
phragm compression driver. Woofer magnet shall be a minimum of
25 oz (708.7 g) and the tweeter shall have a 20 oz (567 g) ceramic mag-
net. The two transducer sections shall be coupled through a built-in 2000
Hz multi-pole crossover network.
Transformer shall be (70.7V / 100V) volt type with 1.9, 3.8, 7.5, 15, 30,
and 60 watt primary taps (@70.7V) with a front mounted tap selector
switch. This tap selector switch shall also include a transformer bypass
setting for instances where the FAP8CXT driver is to be direct coupled to
a low impedance amplifier.
Enclosure shall be a deep drawn steel enclosure design acoustically treat-
ed with fiber lining. Internal volume shall be 937 cubic inches. To facilitate
connection in conduit systems, enclosure shall be equipped with an
access panel covering a recessed terminal cup. This cover shall provide a
combination (19 mm inside diameter) / 1" (25 mm inside diameter) knock-
out on the side access and a top access cover compression fitting/strain
relief to facilitate flexible conduit up to 22 mm outside diameter or 1" (25
mm inside diameter) when the compression fitting is removed.
External wiring shall be accomplished via a removable lockable wiring
connector with screw-down terminals to provide both secure wire ter-
mination and pre-wiring capability before loudspeaker installation. The 4
pole locking connector shall be located in the recessed area behind the
conduit access panel and provide for pass-through connection.
A
⁄
"–20 drop forged eyebolt, factory installed into the top of the enclo-
1
4
sure for additional suspension point when used in drop tile ceilings or for
pendant mounting.
Construction of enclosure shall be a minimum of 18-gauge deep drawn
metal finished in white epoxy.
The system shall include a support backing plate to reinforce the ceiling
material and tile support rails for use on either 2's x 4' (609 mm x
1219 mm) or 2' x 2' (609 mm x 609 mm) suspended ceiling tiles. This
assembly can all be installed from beneath the ceiling tile. If the FAP8CXT
is to be mounted into a suspended ceiling it is required that the system
be supported from above and secured to a structural building member
member approved for this purpose.
Overall front face diameter shall not exceed 15.75" (400 mm); overall
height shall not exceed 11.5" (292 mm), 12.75" (324 mm) including facto-
ry-installed eyebolt.
Grilles shall be press-fit, manufactured from 24-gauge perforated steel
mesh and finished in white epoxy. Round grille shall be 13.67" (347 mm)
diameter.
The loudspeaker shall weigh no more than 13.9 lbs (6.3 kg)
The loudspeaker shall be the Atlas Sound FAP8CXT.
AtlasSound.com
2/4