Bose L1 Model II Instrukcja obsługi - Strona 28

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla System stereo Bose L1 Model II. Bose L1 Model II 32 stron. Portable line array systems
Również dla Bose L1 Model II: Instrukcja obsługi (32 strony), Instrukcja obsługi (28 strony), Arkusz danych technicznych (8 strony), Arkusz danych technicznych (8 strony), Podręcznik aplikacji (13 strony), Podręcznik (15 strony)

Drukuj stronę

Svenska

Nederlands

ARE AND

AINTENANCE

Problem

With nothing plugged into

the power stand, a slight

hum or buzz is heard

B1 bass module is plugged

in, but no bass audio is

heard

B1 bass module sounds

out of balance with the

system

No mid/high sounds heard

from the L1

model II

Cylindrical Radiator

loudspeaker

Instrument or audio source

sounds distorted

Third-party-powered sub-

woofer sounds poor when

connected to the Bass -

Line Out connector on the

power stand

B1 bass modules powered

by a third-party power

amplifier and connected to

the Bass - Line Out

connector sounds poor

Microphone is

encountering feedback

Italiano

Français

Svenska

What to do

• Using an AC outlet tester, test the AC outlet that the power stand is plugged into for

reversed or open (hot, neutral, and/or ground) contacts.

• If using an extension cord, make sure that the cord is also tested as above.

• Make sure you are using the included 4-wire B1 bass module cable.

• Make sure the B1 bass module cable is plugged into the Bass Module Out connector

and the cable plug is fully engaged in the connector.

• Try a different 4-wire cable.

• If available, try a different B1 bass module.

• Make sure you are using the B1 bass module 4-wire cable included with the B1 bass

module package.

• Make sure that the B1 bass module grille is facing forward toward the musicians and

audience.

• Make sure the L1 model II Cylindrical Radiator

seated in their connectors.

• Make sure connections are not bent or broken.

• Try cleaning the contacts on the loudspeaker top and bottom with electronic contact

spray cleaner.

• Make sure the Signal/Clip LED is not constantly red. If it is, lower the trim level.

• Try a different source or instrument.

• Try your source or instrument on another power stand.

• Unplug any B1 bass modules that may be connected to the power stand.

• The signal from the Bass - Line Out may be too high for the powered subwoofer; try

attenuating the signal using commercially available direct boxes or in-line pad devices.

• Try different connections to the third-party-powered subwoofer, such as balanced or

unbalanced cabling and/or a direct box.

• Check that the gain and input controls on the third-party-powered subwoofer are set

appropriately.

• If using a powered subwoofer with an adjustable crossover, set the crossover to 180Hz.

• Ensure that at least two B1 bass modules are directly connected to the Bass Module

Out connector on the power stand using a B1 bass module 4-wire cable.

• Check the gain settings on the third-party power amplifier. The volume level of the B1

bass modules powered by the power stand should be similar to the bass modules pow-

ered by the external amplifier.

• Orient the microphone so that it is not pointing directly at its respective L1 model II

Cylindrical Radiator

• Try a different microphone.

• Try a different position for the loudspeaker and/or vocalist on stage.

• Increase the distance from the loudspeaker to themicrophone.

• If using a vocal effects processor, make sure it is not contributing to the feedback

problem.

Nederlands

Español

loudspeaker.

Français

Deutsch

Italiano

Deutsch

Español

Dansk

loudspeaker top and bottom are firmly

English

Dansk