Bose FreeSpace E4 Series II Instrukcja obsługi - Strona 6
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz Bose FreeSpace E4 Series II. Bose FreeSpace E4 Series II 15 stron. Business music system
Również dla Bose FreeSpace E4 Series II: Instrukcja obsługi (18 strony), Skrócona instrukcja obsługi (4 strony), Instrukcja obsługi (16 strony), Instrukcja obsługi (33 strony)
Drukuj stronę
2.1 Introduction
This section describes the basic steps for designing an E4 sys-
tem and includes an example. It is assumed that a complete
loudspeaker design and layout has already been created.
2.2 Basic design steps
There are five basic steps in designing an E4 system.
2.2.1 Step 1 – Determine source routing
Decide which sources will be played in each area. Create a
"source map" such as the following one that shows which
sources will be played in each major area of the facility.
Source 1
Source 2
●
Area 1
●
Area 2
●
Area 3
●
Area 4
●
Area 5
2.2.2 Step 2 – Determine Auto Volume
requirements
Identify which areas will use Auto Volume. Each Auto Volume
zone must use one Auto Volume user interface and one Bose
sensing microphone to control the volume. A 70/100V volume
control cannot be used.
When using Auto Volume, remember that you will be adjusting
the volume of an overall area. Imagine that you have a dining area
and a bar adjacent to one another. If the sensing microphone is
placed above the bar, the music may become too loud in the din-
ing area. Likewise, if you place the sensing microphone above
2.0 Designing with the E4 System
Source 3
Source 4
●
●
●
the dining area, the music may never be heard in the bar.
Guidelines for establishing Auto Volume zones
Speaker
height is...
>25 ft (7.6 m)
12-25 ft
(3.7-7.6 m)
<12 ft (3.7 m)
Speaker mounting height and the overall quality of the back-
ground noise is used to determine the Auto Volume zoning
requirements. Uniform background noise is found in an area
where no part of the area is louder or quieter than any other. A
●
room with non-uniform background noise would seem louder in
some areas (people talking, machinery running, etc.) and quieter
in others.
Mounting guidelines for sensing microphones
• The sensing microphone must be mounted at the same height
as the loudspeakers or higher. A sensing microphone must
never be mounted lower than the speaker height.
• In all cases, there must be 6 ft (1.8 m), minimum, between the
loudspeaker and the sensing microphone. This is so that the
microphone does not receive signals only from a loudspeaker.
• There must be 35 ft (10.7 m), minimum, between the sensing
®
microphones of two adjacent Auto Volume zones.
• Avoid placing the microphone near unique noise sources like
HVAC equipment, dishwashers, motors, etc.
Separating the microphones as much as possible for two zones
is the best practice. Consider the previous example of the dining
area and a bar adjacent to one another. If each of these areas
uses Auto Volume, it is possible to create a situation in the dining
area where the music is too loud simply because the microphone
15 of 80
Background noise
Background noise
is uniform
is non-uniform
Not recommended
One Auto Volume
One Auto Volume
zone for every
zone for every
3600 ft
2
(324 m
2
)
1800 ft
One Auto Volume
One Auto Volume
zone for every
zone for every
2
2
1800 ft
(162 m
)
900 ft
2
(162 m
2
)
2
2
(81 m
)