DSC CLASSIC PC1555 Instrukcja obsługi - Strona 8
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla System bezpieczeństwa DSC CLASSIC PC1555. DSC CLASSIC PC1555 11 stron.
Drukuj stronęNOTE: If you return and find that an alarm has occurred while you were away, it is possible that
an intruder may still be on the premises. Go to a neighbour's house, and call the local police to
investigate.
The alarm memory is cleared each time the panel is armed so that any alarms showing are
alarms that occurred only during the last armed period.
If An Alarm Sounds
Fire Alarm
If your system has been installed with fire detectors and the bell sounds in a pulsing mode, follow your
emergency evacuation plan immediately (see "Fire Escape Planning" on page 15).
Intrusion Alarm
If an intrusion alarm sounds, indicated by a continuous NMF-1008 buzzer, bell, siren, the alarm may
be silenced by entering your access code. If the alarm was unintentional, call local authorities
immediately to avoid an unnecessary response.
You can determine the source of the alarm by following the instructions in the "Disarming" section (see
page 5). Once the source of the alarm has been corrected, the panel can be restored to its original
Armed state.
Function Keys
Some keypad models have five function keys, located to the right of the number pad, which allow easy
single-button activation of the most commonly used features. If these keys have been enabled by your
installer , you can execute their programmed function by pressing and holding the corresponding key
for two seconds.
For information regarding the operation of the function keys, talk to your alarm installer.
Programming Security Codes
Programming codes from an LED Keypad:
The Master Code
To program the Master Code, enter [ ][5][current Master Code][40][new Master Code]. The Master
Code must be four digits unless otherwise indicated by your installer. Enter digits 0 through 9 only.
Press [#] to return to the Ready state.
Be sure to record your new Master Code on the "System Information" page in this booklet. NOTE: We
recommend that the factory default Master Code [1234] not be used.
Additional Codes
Up to 36 additional codes may be programmed. Codes 01-32 are regular access codes. Codes 33
and 34 are duress codes. Codes 41 and 42 are the system master codes.
To program a new code:
Enter [ ][5][Master code][code number][new access code]. The code number is a double-digit
number from 01-34 or 41-42.
Access codes must be four digits long. Enter digits 0 through 9 only.
To exit code programming, press [#].
6
will flash all 6 zone lights and will beep every second, to indicate that all zones have been bypassed.
When the passkey is removed, a 2-minute exit delay is initiated, during which the keypad will beep
three times every second. After the exit expires, the alarm will return to its normal armed state.
Viewing Trouble Conditions
The control panel continuously monitors a number of possible trouble conditions. If one of these trouble
conditions occur, the keypad will beep twice every 10 seconds until you press any key on the keypad.
NOTE: A TROUBLE condition reduces the security your system is designed to provide. Call your
installing company for service.
To view troubles from an LED Keypad:
A trouble will be indicated by the Trouble light which will remain ON until the trouble condition is cleared.
If you cannot determine or remedy the cause of the trouble condition, contact your installer for
assistance.
To view the type of trouble condition, press [ ][2]. One or more zone lights will turn ON, indicating the
various trouble conditions:
Zone Light Type of Trouble
1 ....... Service required. Call your installation company for service. Press [1] and one or more of
the zone lights corresponding to the following system troubles will turn ON:
........
1. Low Battery
........
2. Bell Circuit Trouble
........
3. General System Trouble
........
4. General System Tamper
2 ....... Indicates the loss of AC power. When this trouble occurs, the Trouble light will turn ON but
the keypad buzzer will not sound.
3 ....... Telephone line trouble.
4 ....... The panel has failed to communicate with the central station.
5 ....... Zone fault. Press [5] and the zone light(s) corresponding to the faulted zones will turn ON.
6 ....... Zone tamper. Press [6] and the zone light(s) corresponding to the tampered zones will turn ON.
7 ....... Low zone battery. This trouble is generated when a wireless device exhibits a low
battery condition.
Press [7] one, two, or three times to view which devices are experiencing battery failure.
The following will occur:
Keypad Beeps Keypad Display
Press [7] ........... 1 .......... Zones with low batteries (LED keypad - zone lights 1 to 8)
Press [7] again .. 2 .......... Handheld keypads with low batteries (LED keypad - zone lights 1 to
4)
Press [7] again .. 3 .......... Wireless keys with low batteries (LED keypad - zone lights 1 to
8). To view the battery conditions of wireless keys 9 through 16, you
must be at an LCD keypad.
5. General System Supervisory
11