DSC LINKS 2150 Instrukcja instalacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla System bezpieczeństwa DSC LINKS 2150. DSC LINKS 2150 12 stron.

Drukuj stronę

Features

• Transmits alarm information to a long range radio network

• Varitech Transmission Format

Note: If automatic SIA is used in the panel, the

reporting codes that are to be sent by the LINKS2150

must still be programmed.

• May be used with the following DSC alarm control

panels:

• PC5010 v1.0 and up

• PC5015 v1.x and up

• PC5008 v2.x and up

• PC1580 v1.0 and up

• PC1565 v2.x and up

• PC1565-2P v2.2 and up

• PC585 v2.x and up

Programmable via Keypad or

Downloading Software

The LINKS2150 is complete with a default program and will

work with a minimum of programming. You can program

the LINKS2150 at any system keypad or using DLS-1 v6.7

or higher.

EEPROM Memory

The LINKS2150 uses EEPROM memory which will retain all

program information even if AC and battery power is

removed. The EEPROM memory can be reprogrammed

thousands of times.

Static/Lightning Protection

The LINKS2150 has been carefully designed and tested to

provide reliable protection against static and lightning

induced transients. Our special "Zap-Trac" circuit board

design catches high voltage transients right at the wiring

terminals, and transient protection devices are placed in

all critical areas to further reduce damaging voltages.

Supervision

• Low or disconnected external battery

• Loss of external AC power

• Security control panel connection supervision

Operation

• Long-range radio alarm transmitter

• 4 LINKS2150 Trouble Reporting Codes and Test

Transmission Reporting Code

Specifications

• 2 negative triggered trouble inputs

- negative voltage trigger: 0 to 0.8 V

• Required power supply: 11.5 to 14V

A separate power supply must be used. Do not power

the LINKS2150 from the keybus.

• Trouble Output: 50mA

• Radio transmitter frequency: as specified on transmitter

• Antenna (not supplied):

- Larsen MHW-450, 50 Ω vertical antenna

- 450 - 470 MHz

• LINKS2150 cabinet dimensions:

- 11" high × 11.8" wide × 3.3"

84mm)

• Cabinet colour: light beige

at 1A

(279 mm × 300 mm ×

Installation

Mounting the LINKS2150

Mount the LINKS cabinet in a convenient location next to

the already installed security system control panel cabinet.

As much as is reasonably possible, do not mount the

LINKS2150 near sources of interference. These include

sources of electrical noise such as computers, televisions

and electric motors in appliances and heating and air

conditioning units, as well as large metal objects like

heating ducts and plumbing which may shield the

antenna. If the cabinet must be located near such items,

the LINKS antenna may have to be mounted on a remote

bracket away from the cabinet. Whenever possible,

mount the LINKS2150 as close as possible to the

security system alarm control panel.

Mounting the Cabinet

If it is not already installed, install and test the security

system according to the instructions found in the security

system's Installation Manual.

Remove the LINKS2150 and mounting hardware from the

cardboard packaging. Before attaching the cabinet to the

wall, press the supplied mounting studs into the raised

mounting holes from the back of the cabinet.

Mount the cabinet securely to the wall. It is recommended

that appropriate wall anchors be used when securing the

panel to drywall, plaster, concrete, brick or other similar

surfaces.

Install the LINKS2150 in the mounted cabinet. Locate the

antenna connection in the hole at the top of the cabinet

and press the LINKS2150 onto the nylon mounting studs.

Insert all cables into the cabinet and prepare them for

connection.

Secure the antenna to the LINKS2150 antenna connector.

Tighten the antenna "finger tight" only.

NOTE: An antenna should always be connected to the

LINKS2150 whenever it is operated. The unit will not

function properly and may be damaged if an antenna is

not installed.

Do not connect the power supply until all other wiring,

including the antenna connection, has been completed

and checked to ensure that it is correct. Incorrect

wiring connections may cause the LINKS unit to

operate improperly, or may damage the LINKS unit.

WARNING:

DO NOT connect both a

PC5400DVACS and a LINKS2150

module to the same system.

You can connect both a PC5400

printer module and a LINKS2150 to

the same system.