DSC PC2580 Instrukcja obsługi - Strona 11
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla System bezpieczeństwa DSC PC2580. DSC PC2580 13 stron.
Drukuj stronęOne Time Use Code
Access Code 16 may be set up on your system to be a One Time Use Code. The One Time Use Code may be
used to disarm and then arm the system only once; after the code is used to arm the system, it will be erased
and may not be used again. This code is designed to be provided to someone such as a baby-sitter or home
service person. Your installer will inform you if the One Time Use Code is enabled on your system. Program
∗
the One Time Use Code by entering [
][5][Master Code][9][8] and then the 4-digit code.
Door Chime On/Off
The Door Chime feature causes the keypad to beep whenever a Door Chime Zone is activated. Your
installer will inform you of which zones on your system will activate the Door Chime feature. This feature is
useful if certain zones are out of view, and you would like an indication of when the zones are opened and
closed. Note that the Door Chime feature only functions when the system is disarmed.
To turn the Door Chime feature ON or OFF, enter [
turned ON, the keypad will sound several beeps. If the feature is being turned OFF, the sounder will
emit a single long tone.
The LCD600 Keypad will display messages while turning the Door Chime feature on and
LCD6OO
off. Refer to Page 21 for instructions on turning the Door Chime feature on and off with
the LCD600 Keypad.
14
∗
][6][Master Code][6]. If the feature is being
ARMING OPTIONS
At-Home Arming
At-Home Arming automatically bypasses certain zones on your system, and also removes the Entry Delay
from the Entry-Exit Zones. This feature allows you to arm the system and remain on the premises. In
addition, if any of the Entry-Exit doors are opened, an alarm will sound instantly. Your installer will inform
you of which zones will be automatically bypassed when At-Home Arming is used.
∗
To use At-Home Arming, enter [
][9][Access Code] on the keypad. The "Armed" light will FLASH to
remind you that there is no Entry Delay on the Entry-Exit doors.
Home-Away Arming
Home-Away arming automatically bypasses certain zones on your system, and applies the Entry Delay to
the Entry-Exit zones. You could use this feature to arm the system and remain on the premises, and
another household member would still be able to enter the premises through the Entry-Exit door without
causing an alarm. When the Entry-Exit door is opened, an Access Code would have to be entered to
disarm the system.
To arm the system with Home-Away Arming, enter an Access Code and do not open the Entry-Exit door.
When the Exit Delay expires, the system will be armed with certain zones automatically bypassed. Your
installer will inform you of which zones will be automatically bypassed when Home-Away Arming is used.
Quick-Exit
When At-Home or Home-Away Arming is used, the Quick-Exit feature allows you to enter [
premises without having to disarm the system.
∗
After entering [
][0], you will have up to 2 minutes to leave the premises through the Entry-Exit Zone.
When the Entry-Exit Zone is closed, the system will remain armed in either the At-Home or Home-Away
modes. If the Entry-Exit Zone is opened after 2 minutes or if there is more than one exit through the zone,
the Entry Delay will begin.
Quick-Arm
∗
The Quick-Arm feature allows you to enter [
someone to arm the system without that person having to be provided with an Access Code. When [
is entered, the Exit Delay will begin and the user may leave the premises through the Entry-Exit door. At
the end of the Exit Delay, the "Armed" light will come ON and the system will be fully armed.
To turn the Quick-Arm feature ON and OFF, enter [
ON, the keypad will beep several times. If Quick-Arm is being turned OFF, the keypad will sound a single
long tone. After turning Quick-Arm ON or OFF, press the [#] Key.
The LCD600 Keypad will display messages while turning the Quick-Arm feature on and
LCD6OO
off. Refer to Page 20 for instructions on turning the Quick-Arm feature on and off with
the LCD600 Keypad.
∗
][0] to arm the system. This command is designed to allow
∗
][6][Master Code][4]. If Quick-Arm is being turned
][0] to leave the
∗
][0]
11