DSC PC5016 Instrukcja obsługi - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla System bezpieczeństwa DSC PC5016. DSC PC5016 11 stron. Tyco power832 security system user manual

Drukuj stronę

1. Access Codes

Viewing Trouble Conditions

The control panel continuously monitors a number of possible trouble conditions. If one of these trouble

conditions occur, the keypad will beep twice every 10 seconds until you press any key on the keypad.

Troubles can only be viewed when the system is in the disarmed state. If a trouble occurs while the

system is armed, enter your access code to disarm the system, then follow the procedure outlined

below to determine the specific trouble.

NOTE: A TROUBLE condition reduces the security your system is designed to provide. Call your

installing company for service.

To view troubles from an LED Keypad:

A trouble will be indicated by the Trouble light which will remain ON until the trouble condition is

cleared. If you cannot determine or remedy the cause of the trouble condition, contact your installer for

assistance.

To view the type of trouble condition, press [ ][2]. One or more zone lights will turn ON, indicating the

various trouble conditions:

ZONE LIGHT

TYPE OF TROUBLE

1 ................. Service required. Press [1] and one or more of the zone lights corresponding to the

following system troubles will turn ON:

1. Low Battery

2. Bell Circuit Trouble

3. General System Trouble

4. General System Tamper

2 ................. Indicates the loss of AC power. When this trouble occurs, the Trouble light will turn

ON but the keypad buzzer will not sound.

3 ................. Telephone line trouble.

4 ................. The panel has failed to communicate with the central station.

5 ................. Zone fault. Press [5] and the zone light(s) corresponding to the faulted zones will turn ON.

6 ................. Zone tamper. Press [6] and the zone light(s) corresponding to the tampered zones will

turn ON.

7 ................. Not used

8 ................. Loss of time on system clock. To set the system time, following the instructions in

"Setting System Date and Time" on page 13.

To view troubles from an LCD Keypad:

From the Ready state, use the arrow (< >) keys to scroll to the following message.

Press [ ] [2] to view the trouble. The message will read...

System Trouble

(*2) to View< >

Use the arrow (< >) keys to view which troubles are present on the system. Once

View Trouble

< >

you have scrolled through the list of troubles, press the [#] key to exit the Trouble

"Trouble Message"

Viewing mode and return to the Ready state.

5. General System Supervisory

6. Not used

7. PC5204 Low Battery

8. PC5204 AC Failure

Alternate Arming Methods

Away Arming

Arming the system in the Away mode will have all interior zones and perimeter zones active. If motion

is detected in the interior zones, or if one of the perimeter zones is violated, the alarm sequence will

begin. To arm in the Away mode, enter your access code and exit the premises through a designated

Exit/Entry door. The system will recognize that occupants have left the premises. Once the exit delay

expires, the system will be fully armed.

Audible Exit Fault

In an attempt to reduce false alarms, the Audible Exit Fault is designed to notify you of an improper

exit when arming the system in the Away mode. In the event that you fail to exit the premises during

the allotted exit delay period, or if you do not securely close the Exit/Entry door, the system will notify

you that it was improperly armed in two ways: the keypad will emit one continuous beep and the bell or

siren will sound. If this occurs, you must re-enter the premises, enter your access code to disarm the

system, and then follow the arming procedure again, making sure to exit the premises in the proper

fashion.

Stay Arming

This feature, if enabled by your installer, will allow you to arm the perimeter zones while leaving the

interior zones inactive so that you can remain on the premises while the system is armed. When you

enter your security code to arm the system and do not exit the premises through a designated Exit/

Entry door, the system will arm in the Stay mode, automatically bypassing the interior zones.

The interior zones can be reactivated at any time by entering [ ][1] at any keypad. If you reactivate

the interior zones, be sure to only inhabit areas not covered by motion detectors. To access areas

protected by motion sensors, you must enter your security code and disarm the system.

Arming Without Entry Delay

If you wish to arm your system without the entry delay, enter [ ][9] then your access code. The Armed

light will flash as a reminder that the system is armed and has no entry delay. An entry through any

zone programmed as a delay zone will create an instant alarm.

Quick Arm

When the Quick Arm feature is enabled, the system may be armed by simply pressing [ ][0] instead of

your access code. Please note that pressing [ ][0] will only allow you to arm the system; to disarm,

you must enter a valid access code. Your installer will inform you if the Quick Arm feature has been

enabled on your system.